Toro Z449 Z Master Скачать руководство пользователя страница 36

Страница: 36 / 60

Charging the Battery

Charging the battery produces gasses that
can explode.

Never smoke near the battery and keep
sparks and ﬂames away from battery.

Important:

Always keep the battery

fully charged (1.265 speciﬁc gravity). This
is especially important to prevent battery
damage when the temperature is below 32°F
(0°C).

1. Charge battery for 10 to 15 minutes at 25 to 30

amps or 30 minutes at 4-6 amps.

2. When the battery is fully charged, unplug

the charger from the electrical outlet, then
disconnect the charger leads from the battery
posts (Figure 41).

Figure 41

1. Positive Battery Post

3. Red (+) Charger Lead

2. Negative Battery Post

4. Black (-) Charger Lead

3. Install the battery in the machine and connect

the battery cables; refer to Installing the
Battery.

Note:

Do not run the machine with the

battery disconnected, electrical damage may
occur.

Servicing the Fuses

The electrical system is protected by fuses. It
requires no maintenance, however, if a fuse blows
check component/circuit for malfunction or short.

Fuse:

•

Main, F1-30 amp, blade-type

•

Charge circuit, F2-25 amp, blade-type

•

Optional head light kit, 10 amp, blade-type

1. Raise the seat to gain access to the fuse holder

(Figure 42).

2. To replace the fuses, pull out on the fuse to

remove it.

3. Install a new fuse (Figure 42).

Figure 42

1. Main, 30 amp

4. Ignition switch

2. Charge circuit, 25 amp

5. Throttle lever

3. For optional head light kit,

10 amp

Содержание Z449 Z Master





























































Результаты поиска

Содержание Z449 Z Master

Отзывы:

Бренды по названию

Популярные бренды

Toro Z449 Z Master, Руководство оператора

Результаты поиска

Содержание Z449 Z Master

Отзывы:

Бренды по названию

Популярные бренды