Toro TimeCutter Z530 Скачать руководство пользователя страница 7

Страница: 7 / 44

Safety and Instructional

Decals

Safety decals and instructions are easily visible to the operator and are located near any
area of potential danger. Replace any decal that is damaged or lost.

93-6677

1. Warning—don’t operate the mower with the deector up or

removed; keep the deector in place.

2. Cutting/dismemberment hazard of hand or foot, mower

blade—stay away from moving parts.

93-7009

1. Warning—don’t operate the mower with the deector up or

removed; keep the deector in place.

2. Cutting/dismemberment hazard of hand or foot, mower

blade—stay away from moving parts.

93-7010

1. Thrown object hazard—keep bystanders a safe distance from

the machine.

2. Thrown object hazard, mower—keep the deector in place.

3. Cutting/dismemberment of hand or foot—stay away from

moving parts.

Manufacturer’s Mark

1. Indicates the blade is identied as a part from the original

machine manufacturer.

110-1868

1. Thrown object hazard, mower—keep the deector in place.

2. Thrown object hazard—Keep bystanders a safe distance from

the machine; Do not operate the without grass collection

system in place.

3. Cutting/dismemberment of hand or foot—stay away from

moving parts.

105-7015

Содержание TimeCutter Z530













































Результаты поиска

Содержание TimeCutter Z530

Отзывы:

Похожие инструкции для TimeCutter Z530

Бренды по названию

Популярные бренды

Toro TimeCutter Z530, Руководство оператора

Результаты поиска

Содержание TimeCutter Z530

Отзывы:

Похожие инструкции для TimeCutter Z530

Бренды по названию

Популярные бренды