Toro TimeCutter 74750 Скачать руководство пользователя страница 27

Страница: 27 / 48

Premaintenance
Procedures

Raising the Seat

Make sure that the motion-control levers are locked in the
P

ARK

position, and lift the seat forward.

The following components can be accessed by raising the seat:

•

Serial plate

•

Service decal

•

Seat-adjustment bolts

•

Fuel filter

•

Battery and battery cables

Lubrication

Greasing the Bearings

Service Interval:

Every 25 hours—Grease all lubrication

points.

Grease Type:

No. 2 lithium grease

Park the machine on a level surface, and disengage the
blade-control switch.

Move the motion-control levers outward to the P

ARK

position, shut off the engine, remove the key, and
wait for all moving parts to stop before leaving the
operating position.

Clean the grease fittings (

Figure 26

and

Figure 27

) with

a rag.

Note:

Make sure to scrape any paint off the front of

the fitting(s).

G014522

Figure 26

Front caster tire

Figure 27

Located on the seat-pan underside

Read the instructions
before servicing or
performing maintenance

Grease every 25 operating
hours

Check the tire pressure
every 25 operating hours

Engine

Connect a grease gun to each fitting and pump grease
into the fittings until grease begins to ooze out of the
bearings (

Figure 26

and

Figure 27

Содержание TimeCutter 74750

















































Результаты поиска

Содержание TimeCutter 74750

Отзывы:

Похожие инструкции для TimeCutter 74750

Бренды по названию

Популярные бренды

Toro TimeCutter 74750, Руководство оператора

Результаты поиска

Содержание TimeCutter 74750

Отзывы:

Похожие инструкции для TimeCutter 74750

Бренды по названию

Популярные бренды