29
Adjusting the Front-to-Rear
Blade Slope
Check the front-to-rear blade level any time you install the
mower. If the front of the mower is more than 5/16 in.
(7.9 mm) lower than the rear of the mower, adjust the blade
level using the following instructions:
1. Position the mower on a flat surface. Disengage the
PTO, set the parking brake, stop the engine, and remove
the key. Disconnect the spark plug wire(s) from the
spark plug(s).
2. Check the air pressure of all four tires. If needed, adjust
to the recommended inflation; refer to Tire Pressure,
page 28.
3. Check and adjust the side-to-side blade level if you
have not checked the setting; refer to Leveling the
Mower from Side-to-Side, page 28.
4. Measure the length of the rear trunion rod (Fig. 38). If
the rod length is not 11-1/2 in. (29.2 cm), remove the
clevis pin and cotter pin from the end of the rod
(Fig. 38), loosen the jam nut, and turn the yoke until the
11-1/2 in. (29.3 cm) dimension is obtained. Then secure
the yoke with the clevis pin and cotter pin. Repeat this
procedure on the opposite side of the mower.
2
3
m–5177
1
11-1/2 in.
(29.2 cm)
4
Figure 38
1.
Rear trunion rod
2.
Clevis pin and cotter pin
3.
Jam nut
4.
Yoke
5. Set the height-of-cut at 3 in. (76 mm) and carefully
rotate the blades so they are facing front to rear
(Fig. 39).
6. Measure between the tip of the front blade (Fig. 39) and
the tip of the rear blade to the flat surface. If the front
blade tip is not 1/16–5/16 in. (1.6–7.9 mm) lower than
the rear blade tip, adjust the front trunion rods.
Front
1078
1
2
3
4
4
Figure 39
1.
Blade front to rear
2.
Measure front blade tip
3.
Measure rear blade tip
4.
Measure here
7. To adjust the front-to-rear blade slope, remove the
hairpin cotter from the front trunion yokes and loosen
the jam nuts (Fig. 40).
m–5178
1
2
3
Figure 40
1.
Front trunion rod yoke
2.
Hairpin cotter
3.
Jam nut
8. Rotate the yokes on the rods to change the adjustment
(Fig. 40). To raise the front of the mower, tighten the
yokes (shorten the rods). To lower the front of the
mower, loosen the yokes (lengthen the rods).
9. After adjusting both trunion rod yokes evenly, secure
the yokes with the hairpin cotters. Check the
front-to-rear level again. Continue adjusting the yokes
until the front blade tip is 1/16–5/16 in. (1.6–7.9 mm)
lower than the rear blade tip (Fig. 39).
10. When the front-to-rear blade slope is correct, tighten the
jam nuts (Fig. 38 and 40).
11. Recheck the side-to-side level of the mower; refer to
Leveling the Mower from Side-to-Side, page 28.
12. Check the height of the anti-scalp rollers; refer to
Adjusting the Anti-Scalp Rollers, page 16.
Содержание TimeCutter 74502
