manualshive.com logo in svg

Toro SIK, Руководство по установке, Страница: 6 / 10

Поделиться
Скачать
Toro SIK Скачать руководство пользователя страница 6

6

correct K Value.

Off_s

: Review your flow sensor’s documentation for its 

correct Offset value.

PPG

 (if Bermad selected): Pulse per gallon based on flow 

meter wiring. See your Bermad flow meter documentation 

for proper setting.

Rain Bucket Configuration

Tip

: The amount of water per tip. The typical rain bucket 

might have a tip point of 0.01”. Check your rain bucket’s 

documentation for correct tip point.

Max

: This is the limit at which the alarm will trip. If the 

Tip unit is 0.01 inch, and the Max limit is 1 inch, it would 

take 100 tips (within the R_win window) to trigger the 

alarm.

Unit

: Select either English or Metric for display of rain 

bucket data in either inches or millimeters.

Alarm

: On or Off. Turn on the alarm 

R_win

: Set the period of time (as a moving window) 

that the controller will calculate rain bucket tips towards 

reaching the max limit.

Act

: If an alarm is triggered, this is the Action that the 

controller will take. Possible choices are:

•  None

. The alarm will only alert the operator.

•  Start Station

. Starts a specified station.

•  Cancel Station

. Cancels a specified station.

•  Cancel All

. Cancels all irrigation activity.

•  Rain Hold

. Places a rain hold on the controller for a 

specified number of days.

Count

: The number of times the rain bucket has filled and 

“tipped”, independent of Alarm status and R_Win setting.

Hr

: Possible to go back in hour increments to review the 

number of tips during that hour from the current time.

H_Cnt

: The number of tips in that hour.

Total

: The number of times the rain bucket has filled and 

“tipped” in the rain window (R_win above) only when the 

alarm is set to On.

Status Sensor Configuration

Sw

: Normally Closed or Normally Open.  

Select the correct setting for your sensor.

Alarm

: Turn the alarm On or Off for the sensor.

QTime

: Qualification time. How long does the alarm 

condition (normally closed becoming open, for example) 

have to stay in that condition for the alarm to be triggered. 

RTime

: Reset time. Clears the alarm automactially if alarm 

condition no longer exists for that period of time.

Act

: If an alarm is triggered, this is the Action that the 

controller will take. Possible choices are:

•  None

. The alarm will only alert the operator.

•  Start Station

. Starts a specified station.

•  Cancel Station

. Cancels a specified station.

•  Cancel All

. Cancels all irrigation activity.

•  Rain Hold

. Places a rain hold on the controller for a 

specified number of days.

Input : 3   Typ:RAIN

Tip   : 0.01 in

Max   : 01.00 in

Unit  : English (in) 

Alarm : On 

R_win : 24hr 

Act   : Rain Hold

Hold  : 02days

Count : 4

Hr: 02 H_Cnt:00001 

Input : 4   Typ:STAT

Sw    : Norm Close

Alarm : On 

QTime : 10s 

RTime : 01m

Act   : Cancel All

Содержание SIK











Отзывы:

Нет отзывов