manualshive.com logo in svg

Toro SIK, Руководство по установке, Страница: 2 / 10

Поделиться
Скачать
Toro SIK Скачать руководство пользователя страница 2

2

Sensor Input Board Installation

1.  Remove the front panel door and power 

down the satellite controller.

2.  Locate an available output board slot to 

install the sensor input board. If the satellite 

is utilizing all output board slots, remove 

the last station output board and use that 

location.

The empty slot might end up being on 

the back side of the controller.
If there are multiple empty slots 

available, the sensor input board 

must be

 

installed in the 

first available slot

 after the 

station output boards.

3.  Install the sensor input board 

A

 and secure 

it with the retaining screw 

1

 and panhead 

screw 

2

.

4.  Install the ribbon cable 

3

 from the 

distribution board to the sensor input board. 

Front installation: Use the short cable. 

Rear installation: Use the longer cable.

5.  Install the fuse 

4

.

6.  If a Surge Board is not already available, 

install the provided Surge board 

B

.  

Secure with three retaining screws 

5

.  

Install two panhead screws 

6

 into Surge 

board for proper grounding.

7.  Restore power to the satellite controller and 

check for proper operation.

3

2

1

4

Figure 1

5

A

B

6

Timing Module (sold separately) Installation

The Sensor Input Board only works with the new Timing 

Module (TM, right) included with the sensor input board 

bundle (VP-SEN-BUNDLE) or purchased separately  

(118-5487SK). If your controller still uses the old TM, you 

must purchase the new TM to take advantage of the VP 

Sensor Input Kit.
Installers must either purchase the Service Kit #118-

5487SK or already have the 118-5487 TM hardware.

Satellite may reset to default settings upon updating 

the firmware version.

Remove the old TM:

1.  Open the lid of the pedestal.

2.  Unscrew the four screws 

1

 that secure the timing 

module into the pedestal.

3.  Remove the TM and unplug the two ribbon cables 

2

.

4.  If there is a modem attached, disconnect the ribbon 

cable to that as well. 

Install the new TM:

1.  Plug the two ribbon cables from step 3 above into the 

new TM.

2.  If there is a modem attached, plug that in.

3.  Set TM into the pedestal and secure with the four 

screws. 

–

+

HOME

%ADJUST

START

PAUSE/

RESUME

STOP

SYSTEM

SETTINGS

MANUAL

WATERING

SCHEDULED

WATERING

DIAGNOSTICS

STATION

SETTINGS

Mode

Central       Local          Off

1

1

1

1

2

The new Timing Module (TM)

Содержание SIK











Отзывы:

Нет отзывов