background image

   PRELIMINARY – For Toro Distributor 

and Toro Company 

use only. 

Part No.

Service Manual

ProForce

R

 Debris Blower

Preface

The purpose of this publication is to provide the service

technician with information for troubleshooting, testing

and repair of major systems and components on the

ProForce Debris Blower.

REFER TO THE OPERATOR’S MANUALS FOR OP-

ERATING, MAINTENANCE AND ADJUSTMENT

INSTRUCTIONS. Space is provided in Chapter 2 of this

book to insert the Operator’s Manuals and Parts Cata-

logs for your machine. Replacement Operator’s Manu-

als are available on the internet at www.toro.com or by

sending complete Model and Serial Number to:

The Toro Company

Attn. Technical Publications

8111 Lyndale Avenue South

Minneapolis, MN  55420

The Toro Company reserves the right to change product

specifications or this publication without notice.

This safety symbol means DANGER, WARNING,

or CAUTION, PERSONAL SAFETY INSTRUC-

TION. When you see this symbol, carefully read

the instructions that follow. Failure to obey the

instructions may result in personal injury.

NOTE:

NOTE

 will give general information about the

correct operation, maintenance, service, testing or re-

pair of the machine.

IMPORTANT: The IMPORTANT notice will give im-

portant instructions which must be followed to pre-

vent damage to systems or components on the

machine.

E

 The Toro Company 

 2008

Содержание ProForce Debris

















































































Отзывы: