background image

Figure 27

1.

Belt

3.

Mounting bolt

2.

Pulley

2. Pivot the pulley mounting bracket away from the

nozzle until the desired belt tension attained.

3. Tighten the mounting bolts.

Electrical Maintenance

Important:

Before welding on the machine,

disconnect the controller and the negative cable
from the battery to prevent damage to the electrical
system.

Fuse

A 15 amp in-line fuse is incorporated into the machines
wiring (Figure 28).

Figure 28

1.

Fuse

Fusible Link

A fusible link is incorporated into the machines wiring.
It is a grey wire located below the in line fuse.

Waste Disposal

Engine oil, engine and remote batteries are pollutants to
the environment. Dispose of these according to your
state and local regulations.

Storage

1. Turn the key to off. Remove spark plug wire.

Remove the key.

2. Remove grass clippings, dirt, and grime from the

external parts of the entire machine, especially the
engine. Clean dirt and chaff from the outside of the
engine’s cylinder head fins and blower housing.

Important:

You can wash the machine with

mild detergent and water. Do not pressure wash
the machine. Avoid excessive use of water.

3. Service the air cleaner; refer to Servicing the Air

Cleaner.

4. Change the crankcase oil; refer to Servicing the

Engine Oil.

5. Check the tire pressure; refer to Checking the Tire

Pressure.

6. Charge the battery; refer to Servicing the Battery.

7. Prepare the machine for storage when non use

occurs over 30 days. Prepare machine for storage
as follows.

A. Add a petroleum based stabilizer/conditioner to

fuel in the tank. Follow mixing instructions from
stabilizer manufacture. Do not use an alcohol
based stabilizer (ethanol or methanol).

Note:

A fuel stabilizer/conditioner is most

effective when mixed with fresh gasoline and
used at all times.

B. Run engine to distribute conditioned fuel through

the fuel system (5 minutes).

C. Stop engine, allow to cool and drain the fuel

tank; refer to Servicing the Fuel Tank.

D. Restart engine and run it until it stops.

E. Choke the engine. Start and run engine until it

will not start.

F. Dispose of fuel properly. Recycle as per local

codes.

Important:

Do not store stabilizer/conditioned

gasoline over 90 days.

24

Содержание ProForce 44538





























Отзывы: