manualshive.com logo in svg

Toro Polar Trac Cab 30474, Руководство оператора

Поделиться
Скачать
Toro Polar Trac Cab 30474 Скачать руководство пользователя страница 49

g032575

Figure 116

1.

Bolt

2.

Washer

5.

Install the summer wheels.

6.

Use a floor jack to lower the summer wheels to
the ground and support the back of the frame
with jack stands (

Figure 115

).

7.

Remove the bolt, washer, and coupler link from
the machine frame (

Figure 117

).

g032572

Figure 117

1.

Coupler link

3.

Bolt

2.

Washer

8.

Roll the winter frame away from the machine
frame (

Figure 118

).

g032768

Figure 118

1.

Winter frame

3.

Jack stands

2.

Machine

9.

Install the rear cover to the cab; refer to

Installing

the Rear Cover (page 36)

.

Installing the Summer
Frame

Connecting the Summer Frame to
the Machine

1.

Align the summer frame to the machine frame
and roll it back (

Figure 119

).

g032769

Figure 119

1.

Summer frame

2.

Machine frame

2.

Align the bolt holes to loosely install the bolts
and spacers on the left side of the machine
(

Figure 121

).

49

 

Содержание Polar Trac Cab 30474





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды