manualshive.com logo in svg

Toro Polar Trac Cab 30474, Руководство оператора

Поделиться
Скачать
Toro Polar Trac Cab 30474 Скачать руководство пользователя страница 50

g032855

Figure 120

1.

Locknut

2.

Bolt (3/4 x 4 inches)

3.

Align the bolt holes to loosely install the bolts
and spacers on the right side of the machine
(

Figure 122

).

g032856

Figure 121

1.

Bolt (3/4 x 4 inches)

2.

Locknut

4.

Torque the bolts to 359 N∙m (265 ft-lb) to secure
the summer frame to the machine frame.

Connecting the Hydraulics to the
Summer Frame

1.

Place a suitable drain pan underneath the valve
and disconnect the hydraulic hoses from the
control valve.

2.

Loosen the supply-hose fitting that is connected
to the gear pump and rotate the supply hose
toward the right side of the machine (

Figure

122

).

g032777

Figure 122

1.

Gear pump

2.

Supply-hose fitting

3.

Use the retaining ring, pivot pin, and bolt to
secure the deck-lift cylinder to the pivot post
(

Figure 123

).

g032735

Figure 123

1.

Retaining ring

3.

Bolt

2.

Lift cylinder

4.

Pivot pin

4.

Install the hydraulic-return hose to the port
marked T on the control valve (

Figure 124

).

50

 

Содержание Polar Trac Cab 30474





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды