Toro Multi Pro 41394 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 96

background image

Fuel System
Maintenance

DANGER

Under certain conditions, fuel and fuel vapors
are highly flammable and explosive. A fire or
explosion from fuel can burn you and others
and can cause property damage.

•

Use a funnel and fill the tank outdoors, in
an open area, when the engine is off and is
cold. Wipe up any fuel that spills.

•

Do not fill the fuel tank completely full.
Add fuel to the fuel tank until the level is 25
mm (1 inch) below the bottom of the filler
neck. This empty space in the tank allows
the fuel to expand.

•

Never smoke when handling fuel, and stay
away from an open flame or where fuel
fumes may be ignited by a spark.

•

Store fuel in a clean, safety-approved fuel
container and keep the cap in place.

Checking the Fuel Line and
Connections

Service Interval:

After the first 50 hours

Every 400 hours/Yearly (whichever comes first)

Inspect the lines and fittings for deterioration, damage,
or loose connections.

Note:

If you find any fuel leaks, repair the fuel

component(s) before operating the machine.

Servicing the Fuel Filter

Service Interval:

Every 400 hours

Removing the Fuel Pump and
Sending Unit

1.

Engage the parking brake, stop the spray pump,
stop the engine, and remove the key.

2.

At the fuel tank, remove the 4 screws (#10 x 3/4
inch) that secure the cover to the top of the fuel
tank, and remove the cover (

).

g032542

Figure 79

1.

Screws (#10 x 3/4 inch)

7.

2-socket connector (fuel
pump/sending unit)

2.

Cover

8.

Nut (fuel pump/sending
unit)

3.

Fuel tank

9.

Seal

4.

2-socket connector
(machine—wiring
harness)

10.

Fuel-hose coupling

5.

2-pin connector (fuel
pump/sending unit)

11.

Fitting (fuel pump)

6.

2-pin connector
(machine-wiring harness)

3.

Disconnect the 2-socket connector of the
machine-wiring harness from the 2-pin
connector of the fuel pump/sending unit;
disconnect the 2-pin connector of the
machine-wiring harness from the 2-socket
connector of the fuel pump/sending unit (

4.

Slide the locking sleeve of the fuel-hose coupling
away from the fitting of the fuel pump/sending
unit and remove the coupling and hose from the
fitting (

Note:

Clean up any fuel that flows from the

hose coupling or fuel-pump fitting.

60

«
...
58
59
60
61
62
...
»

Содержание Multi Pro 41394

































































































Отзывы:

Нет отзывов

Похожие инструкции для Multi Pro 41394

Бренд: Hardi Страницы: 52

Бренд: Graco Страницы: 40

0558001 ProSpray 3.23

Бренд: WAGNER Страницы: 96

Бренд: Graco Страницы: 16

Бренд: Dramm Страницы: 25

Бренд: AG SPRAY Страницы: 6

EASY PAINTER KH-EP02

Бренд: Uni-max Страницы: 8

DANDY-LION KILLER

Бренд: F/S Manufacturing Страницы: 2

Бренд: Kobalt Страницы: 44

Бренд: Kobalt Страницы: 75

Tornado II 51000

Бренд: Blair Страницы: 4

Бренд: ASM Страницы: 38

Бренд: Graco Страницы: 60

MARRO TWIN FORCE 1000

Бренд: Hardi Страницы: 64

COLORKATALOG 2006 D

Бренд: WAGNER Страницы: 22

Бренд: Parkside Страницы: 46

Бренд: Kärcher Страницы: 74

Бренд: Binks Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды