Toro LC175FDS Скачать руководство пользователя страница 46

Страница: 46 / 48

Ignition Coil Gap Adjustment

High Voltage Ignition Systems can be Dangerous

- Use Caution when Servicing Ignition Systems

1. Install the ignition coil and lightly tighten the igniting coil mounting bolts.

2. Rotate engine so ignition coil is aligned with the magnet portion of the flywheel.

3. Insert the feeler gauge between the flywheel and coil.

4. Adjust the ignition coil gap at both side of the coil.

5. Sufficiently tighten the mounting bolts.

Ignition Coil Resistance Inspection

Primary Coil

Place Ohm meter leads between the harness connection

lead and the exposed metal coil leg.

Secondary Coil

Place Ohm meter leads between exposed metal coil leg

and the spark plug terminal connection.

Ignition Coil Gap

0.011-

0.019”

(.3-.5 mm)

A -

Primary Coil Resistance

1.0-1.6

B -

Secondary Coil Resistance

10.5 KΩ +/- 15%

Содержание LC175FDS

















































Результаты поиска

Содержание LC175FDS

Отзывы:

Похожие инструкции для LC175FDS

Бренды по названию

Популярные бренды

Toro LC175FDS, Руководство по обслуживанию

Результаты поиска

Содержание LC175FDS

Отзывы:

Похожие инструкции для LC175FDS

Бренды по названию

Популярные бренды