Toro LC175FDS Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 48

background image

15

Fuel Filter and Hose Replacement

-

Fuel is Extremely Flammable

- Use Extreme Caution When Servicing Fuel System

1. Drain the fuel tank into an approved container.

NOTE:

Ensure fuel system contains no fuel to prevent leak when the fuel filter is replaced.

2. Release the fuel filter / fuel hose clamps (A) and slide them away from the fittings.

3. Remove the fuel filter / hose asm. from the engine.

4. Properly install new fuel filter / hose asm. and clamps (A).

5. Re-fill tank with fresh fuel.

6. Verify hose routing and check for leaks.

7. Properly dispose of any unused fuel.

2

A

Fuel Filter

«
...
17
18
19
20
21
...
»

Содержание LC175FDS

















































Отзывы:

Нет отзывов

Похожие инструкции для LC175FDS

Бренд: VEM Страницы: 27

Бренд: Daihatsu Страницы: 294

MAX-61SX-H RING WC Series

Бренд: O.S. engine Страницы: 36

Бренд: Kuda Страницы: 98

Бренд: Saito Страницы: 27

Lombardini LGW 523 MPI

Бренд: Kohler Страницы: 144

Бренд: Robin Страницы: 63

7-1/2 HP 212cc OHV

Бренд: Power Fist Страницы: 52

Бренд: Leadshine Technology Страницы: 55

A50-10L Turnado

Бренд: Hacker Страницы: 4

Бренд: Hacker Страницы: 36

Бренд: Vanguard Страницы: 124

Бренд: Honda Страницы: 45

Бренд: Baumuller Страницы: 19

Бренд: Baumuller Страницы: 31

ARO AF1060 Series

Бренд: Ingersoll-Rand Страницы: 8

Бренд: Ingersoll-Rand Страницы: 8

Бренд: Ingersoll-Rand Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды