Toro GreensPro 1240 Скачать руководство пользователя страница 185

Страница: 185 / 186

g273555

Figure 94

GreensPro 1260

Transmission cover

Spring washer (3 each)

Bolt (3 each)

Washer (3 each)

Removing the Transmission Cover

1. Tilt the steering column to the full forward position.

2. Release the latch and pivot the seat pan forward.

3. On GreensPro 1240 machines, turn the quick-release screws

counterclockwise 1/4 turn and remove the transmission cover from the
machine (

Figure 93

4. On GreensPro 1260 machines, remove the 3 bolts, 3 spring washers, and 3

washers that secure the transmission cover to the chassis and remove the
transmission cover from the machine (

Figure 94

Installing the Transmission Cover

1. Tilt the steering column to the full forward position.

2. Release the latch and pivot the seat pan forward.

GreensPro

™

1240/1260

Page 7–59

Chassis: Service and Repairs

14211SL Rev A

Содержание GreensPro 1240



























































































































































































Результаты поиска

Содержание GreensPro 1240

Отзывы:

Похожие инструкции для GreensPro 1240

Бренды по названию

Популярные бренды

Toro GreensPro 1240, Руководство по обслуживанию

Результаты поиска

Содержание GreensPro 1240

Отзывы:

Похожие инструкции для GreensPro 1240

Бренды по названию

Популярные бренды