manualshive.com logo in svg

Toro GreensPro 1240, Руководство по обслуживанию, Страница: 139 / 186

Поделиться
Скачать
Toro GreensPro 1240 Скачать руководство пользователя страница 139

Service and Repairs

Drive Chain Idler Arm (GreensPro 1240)

Removing the Drive Chain Idler Arm

1. Park the machine on a clean, level surface with the transport wheels in the

raised and locked position. Shut off the engine. Engage the parking brake if
equipped, or remove the spark plug wire from the spark plug.

2. Remove the transmission cover from the machine; refer to

Removing the

Transmission Cover (page 7–59)

.

3. Remove the hex nut (item 1 in

Figure 63

), spacer, and compression spring

from the idler adjustment rod.

g241025

Figure 63

1.

Hex nut

6.

Flat washer (2 each)

2.

Spacer

7.

Locknut

3.

Compression spring

8.

Pivot bushing

4.

Idler adjustment rod

9.

Spacer

5.

Bolt

10.

Idler arm assembly

4. Remove the bolt, flat washers, locknut, pivot bushing, and spacer that secure

the idler arm to the chassis, and remove the idler arm assembly (

Figure 64

).

GreensPro

™

1240/1260

Page 7–13

Chassis: Service and Repairs

14211SL Rev A

Содержание GreensPro 1240



























































































































































































Отзывы:

Нет отзывов