manualshive.com logo in svg

Toro Greensmaster eTriFlex 04590, Руководство оператора

Поделиться
Скачать
Toro Greensmaster eTriFlex 04590 Скачать руководство пользователя страница 25

Adjusting the Maximum Transport
Speed

Navigate to the M

AX

T

RANSPORT

option to adjust the

maximum transport speed. You can adjust the speed
from 8.0 km/h (5.0 mph) to 16.0 km/h (10.0 mph) in
increments of 0.8 km/h (0.5 mph).

Note:

The factory default setting is 16.0 km/h (10.0

mph).

Adjusting the Maximum Reverse
Speed

Navigate to the M

AX

R

EVERSE

option to adjust the

maximum reverse speed. You can adjust the speed
from 3.2 km/h (2.0 mph) to 4.8 km/h (3.0 mph) in
increments of 0.8 km/h (0.5 mph).

Note:

The factory default setting is 4.0 km/h (2.5

mph).

Setting the Slow and Turn Function

Navigate to the S

LOW

& T

URN

option to set the slow

and turn function. The slow and turn function slows
the machine speed while you turn the machine for
another cutting pass on a green.

Note:

The factory default setting is O

FF

.

Disabling an Equipped
3-Wheel-Drive Kit

Navigate to the 3WD K

IT

option to disable an equipped

3-Wheel-Drive Kit.

If you choose to disable this option, the kit will be
enabled again if you cycle the key switch (i.e., turn
off, then turn on the machine) with an equipped
3-Wheel-Drive Kit.

Note:

When you install the 3-Wheel-Drive Kit, the kit

is automatically enabled.

Setting the Battery-Reserve
Capacity

Navigate to the B

ATT

. R

ESERVE

option to set the

amount of distance needed to transport the machine
to the shop. This allows you to have enough battery
power (when the battery level becomes too low) to
transport the machine to the shop for recharging; refer
to

Monitoring the Battery-System Charge Level (page

30)

.

Note:

You can adjust the distance from 0.8 km (0.5

mi) to 8 km (5 mi) in 0.8 km (0.5 mi) increments.

Understanding the
InfoCenter Dialog
Messages

When the machine is being calibrated, dialog
messages appear in the InfoCenter. These messages
are intended to instruct you through the calibration
process.

Refer to the following table for a list of each dialog
message:

Dialog Messages

Message
Number

InfoCenter Message Text

1

Return pedal to neutral

4

Move pedal to max forward and hold

5

Max forward calibration passed

9

Max forward calibration failed. Voltage out of spec

13

Move pedal to max reverse and hold

14

Max reverse calibration passed

16

Max reverse calibration failed. Voltage out of spec

17

Calibration failed. Pedal position unknown

18

Return pedal to neutral. Continue?

100

Calibration is engaged

101

Calibration is complete

102

Cycle the key switch

110

Inhibit calibration. Component not responding

111

Inhibit calibration. Component not ready

112

Inhibit calibration. Fault active

113

Inhibit calibration. Not in seat

114

Inhibit calibration. Not in neutral

115

Inhibit calibration. In neutral

116

Inhibit calibration. Parking brake is engaged

300

Return pedal to neutral

301

Center steering wheel. Continue?

302

Manually center rear wheel. Continue?

303

Steer rear wheel max left. Continue?

304

Steer rear wheel max right. Continue?

305

Rear wheel center out of range

306

Rear wheel angle out of range

400

Caution: Machine must be on jack stands.
Continue?

401

Inhibit calibration. Contactor open

402

Inhibit calibration. Pedal in Neutral

403

Return pedal to neutral

25

 

Содержание Greensmaster eTriFlex 04590

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды