background image

Part No. 04133SL 

Service Manual 

Greens Aerator 

Preface 

The purpose of this publication is to provide the service 
technician with information for troubleshooting, testing 
and repair of major systems and components on the 
Greens Aerator. 

REFER TO THE OPERATOR’S MANUALS FOR OP-
ERATING, MAINTENANCE AND ADJUSTMENT 
INSTRUCTIONS. Space is provided in Chapter 2 of this 
book to insert the Operator’s Manuals and Parts Cata-
logs for your machine. Replacement Operator’s Manu-
als are available on the internet at www.toro.com or by 
sending complete Model and Serial Number to: 

The Toro Company 
Attn. Technical Publications 
8111 Lyndale Avenue South 
Minneapolis, MN  55420 

The Toro Company reserves the right to change product 
specifications or this publication without notice. 

or CAUTION, PERSONAL SAFETY INSTRUC-

This safety symbol means DANGER, WARNING, 

TION. When you see this symbol, carefully read 
the instructions that follow. Failure to obey the 
instructions may result in personal injury. 

NOTE:  NOTE will give general information about the 
correct operation, maintenance, service, testing or re-
pair of the machine. 

IMPORTANT: The IMPORTANT notice will give im-
portant instructions which must be followed to pre-
vent damage to systems or components on the 
machine. 

 The Toro Company – 2004 

Содержание Greens Aerator



































































































































Отзывы: