manualshive.com logo in svg

Toro 79155, Руководство оператора

Поделиться
Скачать
Toro 79155 Скачать руководство пользователя страница 18

Tips and Troubleshooting  

1.  When the bags get full, there will be 

slight blowout from the front right corner 
of the deck.  Emptying the bags at this 
point will minimize the potential for the 
tube to plug. 

2.  If there is excessive blowout from the 

deck, check to make sure that the rear 
screen in the hood is clear of grass build 
up.  It is recommended that the screen 
and mesh portions of the bags be 
cleaned regularly to maintain proper air 
flow.  This is especially important in wet 
conditions. 

3.  During dry conditions check engine air 

cleaners and clean cooling fins more 
frequently.  The bagger has been 
designed to minimize the impact of dust 
and debris on the mower, but bagging 
can be a dirty environment. 

4.  During dry conditions, switching to a 

lower lift blade may reduce blowout 
without hurting quality of cut. 

5.  Maintaining a ground speed that does not 

pull down the engine RPM will allow for 
the highest productivity and best quality 
of cut.  Bogging the engine RPM down by 
going too fast will cause plugging and 
quality of cut issues. 

6.  When storing the bagger, it is 

recommended that any grass build up in 
the tubes be cleaned out.  

 

 

 

 

 

 

 

 

 

 

 

 

 

Changing Blades 

1.  Install the blade onto the spindle shaft 

(Figure 16). 

Important: The curved part of the blade 
must be pointing upward toward the 
inside of the mower to ensure proper 
cutting.

 

 

 
 
 
 
 
 
 
 
 
 
 

Figure 16

 

1.  Blade   

 

2.  Sail area of blade

 

3.  Bushing 

 

4.  Spring disk washers

 

5.  Blade bolt 

 

+

  Orientation of washers

 

 

2.  Hold the blade end using a rag or thickly-

padded glove (or place a wrench on the 
top sheave nut).  Install the bushing, two 
spring disk washers (cupped side toward 
the blade) and blade bolt (Figure 16).  

3.  Torque the blade bolt to 45-55 ft-lbs  

   

   

(61-75 N-m). 

 

Incorrect installation of the blade or 
components used to retain the blade 
cause the blade to come loose and 
could seriously injure or kill you or 
bystanders.

 

Always install the original Toro blades, 
blade bushing, spring disk washers and 
blade bolts as shown.  

 

 

Note:  Refer to mower 

Operator’s Manual

 for 

complete blade maintenance.

 

 

+

18 

Содержание 79155





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды