Toro 74593 Скачать руководство пользователя

Страница: 38 / 40

Problem

Possible Cause

Corrective Action

1. The blades are bent or unbalanced.

1. Install a new blades.

2. The blade mounting screws are loose.

2. Tighten the blade mounting screws.

3. The engine mounting bolts are loose.

3. Tighten the engine mounting bolts.

4. There is a loose engine pulley, idler

pulley, or blade pulley.

4. Tighten the appropriate pulley.

5. The engine pulley is damaged.

5. Contact an Authorized Service Dealer.

There is abnormal vibration.

6. The blade drive belt is damaged.

6. Install a new blade drive belt.

1. The blade drive belt is worn, loose, or

broken.

1. Install a new blade drive belt.

2. The blade drive belt is off the pulley.

2. Install the blade drive belt and adjust it

for the correct tension.

The blades do not rotate.

3. The grass collector is not in place.

3. Install the grass collector.

1. The tire pressure is incorrect.

1. Set the tire pressure.

2. The mower is not level.

2. Adjust the height adjustment cable rod

assembly.

3. The underside of the mower is dirty.

3. Clean the underside of the mower.

4. The blade mounting screws are loose.

4. Tighten the blade mounting screws.

The cutting height is uneven.

5. The blade drive belt tension is incorrect.

5. Adjust the blade drive belt.

The cruise control will not engage or will
not stay engaged.

1. The battery is not fully charged.

1. Charge the battery.

Содержание 74593









































Результаты поиска

Содержание 74593

Отзывы:

Похожие инструкции для 74593

Бренды по названию

Популярные бренды

Toro 74593, Руководство оператора

Результаты поиска

Содержание 74593

Отзывы:

Похожие инструкции для 74593

Бренды по названию

Популярные бренды