background image

22

Maintenance

Checking the Fuel Cap

The fuel cap contains a non-serviceable filter and check 
valve. A clogged fuel filter causes poor engine perfor-
mance. If performance improves when the fuel cap is 
loosened, the check valve may be faulty or the filter may 
be clogged. Replace the fuel cap if necessary.

Cleaning the Air Filter

See Figure 20 and Figure 22.

Clean the air filter as indicated by the maintenance 
schedule.

Follow these steps to clean the air filter.

1.

Stop the trimmer.

2.

Remove the spark plug boot.

3.

Loosen the air filter cover by turning the knob coun-
terclockwise.

4.

Remove the air filter cover.

5.

Remove the air filter.

6.

Clean the air filter with warm soapy water.

7.

Rinse the air filter and let it dry completely.

8.

Work two drops of oil into the air filter.

9.

Replace the air filter (fits only one way).

10.

Replace the air filter cover.

11.

Tighten the air filter cover by turning the knob 
clockwise.

12.

Replace the spark plug boot.

Note:

 Replace the air filter (Part No. 88048) as indi-

cated by the maintenance schedule.

Figure 20

Cleaning the Spark Arrester

See Figure 21.

Follow these steps to clean the spark arrester.

1.

Locate the spark arrester through the hole on the 
muffler-side engine cover.

2.

Remove the spark arrester by pulling it out with nee-
dle-nosed pliers.

3.

Clean the spark arrester with a small wire brush.

4.

Replace the spark arrester.

Figure 21

WARNING:

A leaking fuel cap is a fire hazard and must be 
replaced immediately.

WARNING:

Make sure the trimmer head stops rotating when 
you release the trigger. Contact with a rotating 
trimmer head could cause personal injury.

Air

Filter

Air

Filter

Cover

Knob

Spark

Arrester

Содержание 51930





























Отзывы: