background image

Maintenance

21

11.

Repeat the process for the lower threaded area of the 
spool, winding the line and securing it in the slotted 
tab opposite the first secured line.

12.

Insert the lines into the eyelets on the trimmer head.

13.

Place the spool on the drive shaft.

Note:

 To install the spool, you may need to rotate it 

slightly. If the line should tangle or break at the eye-
let, remove the spool, refeed the line through the eye-
lets, and reassemble the spool on the trimmer.

14.

Release the lines from the tabs by sharply pulling 
each line.

15.

Push down on the spool to reveal the threads inside 
the drive shaft.

16.

Thread the retaining cap

 

on the drive shaft.

17.

Secure the retaining cap.

18.

Replace the spark plug boot. 

See Figure 22.

Figure 18

Replacing the Spool

See Figure 19.

Note:

 For best performance, use only Toro spools (Part 

No. 88046). The spool may wear during normal use of 
the line advance feature and may require occasional 
replacement. Replacement spools are available through 
your Toro retailer.

Follow these steps to replace the spool.

1.

Stop the trimmer.

2.

Remove the spark plug boot. 

See Figure 22.

3.

Remove the retaining cap by turning as indicated by 
the arrow on the cap.

4.

Remove the empty spool.

5.

Clean the trimmer head thoroughly. Inspect the 
trimmer head for any damaged or worn parts.

6.

Remove the lines from the slotted tabs on the spool 
and unwind approximately six inches.

7.

Secure the lines temporarily by pushing them into 
the slotted tabs on the spool.

8.

Insert the lines of the new spool into the eyelets on 
the trimmer head.

9.

Place the spool on the drive shaft.

Note:

 To install the spool, you may need to rotate it 

slightly.

Note:

 If the line should tangle or break at the eyelet, 

remove the spool, refeed the line through the eyelets, 
and reassemble the spool on the trimmer.

10.

Release the lines from the tabs by sharply pulling 
each line.

11.

Push down on the spool to reveal the drive shaft.

12.

Thread the retaining cap on the drive shaft.

13.

Secure the retaining cap.

14.

Replace the spark plug boot. 

See Figure 22.

Figure 19

WARNING:

An improperly installed retaining cap or spool 
could fly off the trimmer. Contact with a thrown 
retaining cap or spool could cause personal injury.

Upper

Lower

Inner Ring

 Threaded Area

Threaded Area

 Slotted 

Tab

WARNING:

Make sure the trimmer head stops rotating when 
you release the trigger. Contact with a rotating 
trimmer head could cause personal injury.

Retaining

Cap

Spool

Trimmer

Head

Drive

Shaft

Eyelet

Slotted

Tab

Содержание 51930





























Отзывы: