Toro 46405AA Скачать руководство пользователя страница 6

3

Inspecting the Machine

No Parts Required

Checking the Traction Unit
Requirements

Use the following list as a reference:

Refer to

Specifications (page 6)

for the minimum

horse power and minimum lifting capacity for the
traction unit.

The traction unit must have a category I or II
3-point hitch.

Adequate front-end weight (ballast) to offset the
weight of the machine.

Check the tire air pressure of the traction unit.

Adjust the tire air pressure as needed.

Important:

Do not exceed the maximum

or minimum tire inflation pressures as
recommended by the tire manufacturer.

Checking the Ballast
Requirements

WARNING

Mounting the machine to the rear of the
traction unit decreases the weight on its front
axle. Failure to add required ballast may result
in an accident and severe injury or death.

To ensure adequate steering control and
stability, you may need to add ballast to
the front of the traction unit.

Refer to the traction unit operator's manual
for ballast requirements.

Product Overview

Specifications

Specifications and design are subject to change
without notice.

Traction Unit Requirements

Lifting capacity

500 kg (1,103 lb)

Minimum output-power rating

22 Kw (30 hp)

Tow system

3-point hitch, category 1 or 2

Attachment Specifications

Width

1.8 m (71 inches)

Length

77.5 cm (31 inches)

Height

150 cm (59 inches)

Maximum transport and
working speed

12 km/h (7.5 mph)

Maximum capacity

21,600 m

2

/h (232,500 ft

2

/h)

Weight

150 kg (331 lb)

Attachments/Accessories

A selection of Bullseye approved attachments and
accessories may be available for use with the machine
to enhance and expand its capabilities. Contact your
Authorized Service Dealer or authorized Bullseye
distributor or go to www.Toro.com/Bullseye for a list of
all approved attachments and accessories.

To ensure optimum performance and continued safety
certification of the machine, use only genuine Bullseye
replacement parts and accessories. Replacement
parts and accessories made by other manufacturers
could be dangerous, and such use could void the
product warranty.

Note:

The Wing Kit and Towable Lift Kit are not

compatible together.

6

 

Содержание 46405AA

















Отзывы: