Toro 38870 Скачать руководство пользователя

Страница: 28 / 94

Engine Replacement

Engine Removal

1. Park the machine on a level surface. Stop the engine, wait for all moving

parts to stop and remove the key.

2. Remove the traction belt.

Traction Belt Removal (page 7–7)

3. Remove the 2 (1/4–20 x 1 inch) bolts securing the QUICK STICK® rod.

Remove the QUICK STICK® rod.

4. Remove the 2 (15 mm) nuts securing the LH engine to the LH engine plate.

Repeat on the RH side of the machine.

g263346

Figure 4

5. Using a proper lifting device, lift the engine away from the machine.

Engine Installation

1. Using a proper lifting device, place the engine into position on the machine.

2. Apply loctite and install the 2 (15 mm) nuts securing the LH engine to the LH

engine plate. Torque the nuts to 12.25 ± 1.7 N • m (150 ± 15 in-lb). Repeat
on the RH side of the machine.

Engine: Service and Repairs

Page 4–4

POWER TRX™ HD Service Manual

3440-740 Rev A

Содержание 38870































































































Результаты поиска

Содержание 38870

Отзывы:

Похожие инструкции для 38870

Бренды по названию

Популярные бренды

Toro 38870, Руководство по обслуживанию

Результаты поиска

Содержание 38870

Отзывы:

Похожие инструкции для 38870

Бренды по названию

Популярные бренды