Toro 38063 Скачать руководство пользователя страница 26

Страница: 26 / 28

Troubleshooting

Toro designed and built your snowthrower for trouble-free operation. Check the following components and items carefully,
and refer to Maintenance on page 18 for more information. If a problem continues, see an Authorized Service Dealer.

Problem

Possible Causes

Corrective Action

Electric starter does not turn
(electric-start models only)

1. The power cord is

disconnected at the outlet or
the snowthrower.

1. Connect the power cord to the

outlet and/or the snowthrower.

2. The power cord is worn,

corroded, or damaged.

2. Replace the power cord.

3. The power outlet is not

energized.

3. Have a qualified electrician

energize the power outlet.

Engine does not start or starts

1. The key is not in the ignition or

1. Insert the key into the ignition

Engine does not start or starts
hard

1. The key is not in the ignition or

is in the

Off position.

1. Insert the key into the ignition

and turn it to the

On position.

2. The choke is in the

Off position

and the primer has not been
pressed.

2. Move the choke to the

position and press the primer
three times.

3. The fuel shutoff valve is not

open.

3. Open the fuel shutoff valve.

4. The throttle is not in the

Fast

position.

4. Move the throttle to the

Fast

position.

5. The fuel tank is empty or the

fuel system contains stale fuel.

5. Drain and/or fill the fuel tank

with fresh gasoline (not more
than 30 days old). If the
problem persists, contact your
Authorized Service Dealer.

6. The spark plug wire is loose or

disconnected.

6. Connect the wire to the spark

plug.

7. The spark plug is pitted, fouled,

or the gap is incorrect.

7. Check the spark plug and

adjust the gap if necessary.
Replace the spark plug if it is
pitted, fouled, or cracked.

8. The fuel cap vent is restricted.

8. Remove the vent restriction or

replace the fuel cap.

9. The engine oil level in the

engine crankcase is too low or
too high.

9. Add or drain oil to adjust the oil

level in engine crankcase to the
Full mark on the dipstick.

10.The air temperature is above

F (4

C) and the carburetor

heater box is on the
snowthrower.

10.Remove the carburetor heater

box.

Engine runs rough

1. The choke is in the

On position.

1. Move the choke to the

Off

position.

2. The fuel shutoff valve is not

completely open.

2. Open the fuel shutoff valve.

Содержание 38063





























Результаты поиска

Содержание 38063

Отзывы:

Бренды по названию

Популярные бренды

Toro 38063, Руководство оператора

Результаты поиска

Содержание 38063

Отзывы:

Бренды по названию

Популярные бренды