background image

12

1

1

Figure 8

1.

Motor mounting screws

3. Remove lynch pin or retaining nut (GM4700 only)

securing deck carrier frame to lift arm pivot pin (Fig. 9).

1

2

Figure 9

1.

Lynch pin

2.

Lift arm pivot pin

4. Roll the cutting deck away from the traction unit.

Mounting the Cutting Decks to
the Traction Unit

1. Position machine on a level surface and shut engine off.

2. Move cutting deck into position in front of traction unit.

3. Slide deck carrier frame onto lift arm pivot pin. Secure

with lynch pin or retaining nut (GM 4700 only) (Fig. 9).

4. Install hydraulic motor to deck (Fig. 8). Make sure

O-ring is in position and not damaged.

5. Grease spindle.

Blade Plane

The rotary deck comes from the factory preset at 2.00 inch
height-of-cut and blade rake of 0.310 inch. The left-hand
and right-hand heights are also preset to within 

±

0.030 inch

of the other.

The cutting deck is designed to withstand blade impacts
without deformation of the chamber. If a solid object is
struck, inspect the blade for damage and blade plane for
accuracy.

Inspecting the Blade Plane

1. Remove hydraulic motor from cutting deck and remove

cutting deck from tractor.

2. Use hoist (or minimum of two people) and place cutting

deck on flat table.

3. Mark one end of blade with paint pen or marker. Use

this end of blade to check all heights.

4. Position cutting edge of marked end of blade at 12

o’clock (straight ahead in direction of mowing)
(Fig. 10) and measure height from table to cutting edge
of blade.

12 o’clock

6 o’clock

9 o’clock

3 o’clock

Figure 10

5. Rotate marked end of blade to the 3 and 9 o’clock

positions (Fig. 10) and measure heights.

6. Compare 12 o’clock measured height to the height of

cut setting. It should be within .030 inch. The 3 and 9
o’clock heights should be .150

±

.030 inch higher than

the 12 o’clock setting and within .030 in. of each other.

If any of these measurements are not within specification,
proceed to Adjusting the Blade Plane, page 13.

Содержание 30827





















Отзывы: