manualshive.com logo in svg

Toro 30413, Руководство оператора

Поделиться
Скачать
Toro 30413 Скачать руководство пользователя страница 47

Figure 66

1.

Hydraulic motor

2.

Mounting bolts

5. Remove the old belt from around the spindle pulleys

and idler pulley.

6. Route the new belt around the spindle pulleys and

idler pulley assembly.

7. Position the hydraulic motor on the cutting unit after

routing the belt around the pulleys. Mount the motor
to the cutting unit with the bolts previously removed.

Note:

Make sure the belt is positioned on the spring

side of the belt guide (Figure 65).

8. Reconnect the extension spring (Figure 65) to the

eye bolt and tension the belt as follows:

•

When properly tensioned, the extension
spring (hook to hook) measurement should be
approximately 3.50 ±.25 inch (inside).

•

Once the correct spring tension is attained,
adjust the stop bolt (carriage bolt) until there is
approximately .125 +.060/-.000 inch clearance
between the head of the bolt and the idler arm.

Controls System
Maintenance

Adjusting the Throttle Cable

Service Interval:

After the first 50 hours

Every 400 hours

Adjust the throttle cable (Figure 67) so that the governor
lever on the engine contacts the low and high speed set
bolts before the throttle lever contacts the slot in the
control panel.

Figure 67

1.

Throttle cable

Adjusting the Traction Pedal
Linkage

The traction pedal should reach full stroke at the same
time it makes contact with the stop. If it does not,
perform the following procedure:

1. Park the machine on a level surface, stop the engine,

and lower the cutting units to the floor. Remove the
ignition key.

2. Check the traction pedal stop adjustment. The

distance from the top of the stand to the top of
the stop must be 1-1/2 inch (38 mm) (Figure 68).
Loosen the nuts and adjust, as required.

47

Содержание 30413

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды