Toro 30413 Скачать руководство пользователя страница 11

Страница: 11 / 64

114-5604

(Affix over part no.

114–5605 for CE*)

* This safety decal includes a slope warning required on the machine for compliance to the European Lawn Mower Safety Standard EN836:1997. The conservative maximum

slope angles indicated for operation of this machine are prescribed by and required by this standard.

Warning—read the

Operator’s Manual.

Warning—do not operate this machine unless you are trained.

Thrown object hazard—keep bystanders a safe distance from the machine.

Warning—wear the seat belt when seated in the operator’s position.

Cutting hazard of hand or foot—stay away from moving parts; keep all guards in place.

Tipping hazard—lower the cutting unit when driving down slopes; do not operate on slopes greater than 15 degrees.

Warning—lock the parking brake, stop the engine and remove the ignition key before leaving the machine.

106-6753

Engine coolant under pressure

Explosion hazard—read the

Operator’s Manual

Warning—do not touch the hot surface.

Warning—read the

Operator’s Manual

106-6754

Warning—do not touch the hot surface.

Cutting/dismemberment hazard, fan and entanglement
hazard, belt—stay away from moving parts.

106-6755

Engine coolant under
pressure.

Warning—do not touch
the hot surface.

Explosion hazard—read
the

Operator’s Manual.

Warning—read the

Operator’s Manual.

115-8474

Power outlet

Starter solenoid

Seat switch

Light Kit

Ignition switch

Fan

Power Take Off (PTO)

Power seat

Содержание 30413

































































Результаты поиска

Содержание 30413

Отзывы:

Бренды по названию

Популярные бренды

Toro 30413, Руководство оператора

Результаты поиска

Содержание 30413

Отзывы:

Бренды по названию

Популярные бренды