manualshive.com logo in svg

Toro 30150, Руководство оператора

Поделиться
Скачать
Toro 30150 Скачать руководство пользователя страница 32

32

m–5389

Figure 41

3. Lubricate the blade belt idler arm pivot (Fig. 42) after

every 50 operating hours.

m-4749

Figure 42

Servicing the Brakes

Service Interval/Specification

Before each use, check brakes for proper operation.

Always set the parking brake when you stop the machine or
leave it unattended. If the parking brake does not hold
securely, an adjustment is required.

Checking the Brakes

1. Park the machine on a level surface, disengage the

blade control (PTO) and set the parking brake.

2. Rear wheels must lock when you try to push the

machine forward or backward. Adjustment is required if
the wheels turn and do not lock; refer to Adjusting the
Brake, page 32.

3. Release the brake and press upper control bar very

lightly, approximately 1/2 inch (13 mm), wheels should
rotate freely.

4. If both conditions are met, no adjustment is required.

Adjusting the Brakes

The brake lever is on the upper control bar (Fig. 16). If the
parking brake does not hold securely, an adjustment is
required.

1. Check the brake before you adjust it; refer to Checking

the Brake, page 32.

2. Release the parking brake; refer to Releasing the

Parking Brake, page 19.

3. To adjust brake set the parking brake latch, and rotate

the wing nuts on the brake rods (Fig. 43). Clockwise to
tighten the brake and counterclockwise to loosen the
brake.

Note: Control bar should be parallel with reference bar
when properly adjusted.

4. Check the brake operation again; refer to Checking the

Brake, page 32.

Important

 

With the parking brake released, the rear

wheels must rotate freely when you push the mower. If
brake action and free wheel rotation cannot be achieved
contact your service dealer immediately.

Содержание 30150













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды