background image

 2 

 

This product complies with the US National Highway Traffic 
Safety Administration (NHTSA) regulations for street legal 
trailers. 

WARNING 

The engine exhaust from this product contains chemicals 
known to the State of California to cause cancer, birth 
defects, or other reproductive harm. 

This spark ignition system complies with Canadian  
ICES-002. 

In some areas, there are local, state, or federal regulations 
requiring that a spark arrester be used on the engine of this 
machine. A spark arrester is not incorporated with the muffler 
assembly. 
 

Important

 

This engine is not equipped with a spark arrester 

muffler. It is a violation of California Public Resource Code 
Section 4442 to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land without a spark 
arrester muffler maintained in working order, or the engine 
constricted, equipped, and maintained for the prevention of 
fire. Other states or federal areas may have similar laws.

 

 
The enclosed Engine Owner’s Manual is supplied for 
information regarding the US Environmental Protection 
Agency (EPA) and the California Emission Control 
Regulation of emission systems, maintenance, and 
warranty. Replacements may be ordered through the 
engine manufacturer. 

INTRODUCTION 

This brush chipper is designed to chip branches, vines, leaves, 
and small tree limbs up to 6 in. (15.24 cm) in diameter. It is 
not intended to chip rocks, wire, metal, or any materials other 
than wood. The brush chipper can be towed behind a vehicle 
equipped with an appropriate ball hitch. 

You may contact Toro directly at www.Toro.com for product 
and accessory information, help finding a dealer, or to register 
your product. 

Read this information carefully to learn how to operate and 
maintain your product properly and to avoid injury and 
product damage. You are responsible for operating the 
product properly and safely. 

Whenever you need service, genuine Toro parts, or additional 
information, contact an Authorized Service Dealer or Toro 
Customer Care and have the model and serial numbers of 
your product ready. Write the numbers in the space provided. 

This Manual identifies potential hazards and has safety 
messages identified by the safety alert symbol, (Figure 1) 
which signals a hazard that may cause serious injury or death 
if you do not follow the recommended precautions.  

 

 

Figure 1 

1. Safety alert symbol 

 
This manual uses two other words to highlight information. 

Important

 calls attention to special mechanical information 

and 

Note

 emphasizes general information worthy of special 

attention. 

Tire Information 

The tire identification number (TIN) is branded into the 
sidewall of all street legal tires (Figure 2). 

 

Figure 2 

1. Tire identification number (TIN) 

 

SAFETY 

Hazard control and accident prevention are dependent 
upon the awareness, concern, and proper training of the 
personnel involved in the operation, transport, 
maintenance, and storage of the machine. Improper use or 
maintenance of the machine can result in injury or death. 
To reduce the potential for injury or death, comply with 
the following safety instructions. 

Safe Operating Practices 

This product is capable of crushing and amputating hands and 
feet. Always follow all safety instructions to avoid serious 
injury or death. 

WARNING 

Engine exhaust contains carbon monoxide, an odorless, 
deadly poison that can kill you. 

Do not run the engine indoors or in an enclosed area. 

 
If you believe that your vehicle* has a defect which could 
cause a crash or could cause injury or death, you should 
immediately inform the National Highway Traffic Safety 
Administration (NHTSA) in addition to notifying The Toro 
Company. 
 
If NHTSA receives similar complaints, it may open an 
investigation, and if it finds that a safety defect exists in a  

Содержание 22604





















Отзывы: