manualshive.com logo in svg

Toro 22302, Руководство оператора, Страница: 42 / 44

Поделиться
Скачать
Toro 22302 Скачать руководство пользователя страница 42

Troubleshooting

40

PROBLEM

CORRECTIVE ACTION

POSSIBLE CAUSES

Excessive black smoke from
exhaust (continued).

6.

Excessive loading.

6.

Reduce load; use lower
ground speed.

Excessive white smoke from
exhaust.

1.

The engine temperature is
low.

1.

Check the thermostat.

2.

The glow plugs are
inoperative.

2.

Check the fuse, glow plugs
and wiring.

3.

The fuel injection nozzles are
faulty.

3.

Contact your Authorized
Service Dealer.

4.

The injection pump timing is
incorrect.

4.

Contact your Authorized
Service Dealer.

5.

Low compression.

5.

Contact your Authorized
Service Dealer.

Machine does not drive.

1.

Traction pump drive coupler
is loose or broken.

1.

Contact Authorized Service
Dealer.

2.

Hydro fluid level low.

3.

Pump and/or wheel motor is
defective or damaged.

4.

Control valve is defective or
damaged.

5.

Relief valve is defective or
damaged.

6.

Flow divider valve lever is in 
9 o’clock position.

2.

Add hydro fluid to reservoir.

3.

Contact  Service Dealer

4.

Contact  Service Dealer

5.

Contact  Service Dealer

6.

Move lever to 12 o’clock to 
10 o’clock position.

Содержание 22302













































Отзывы:

Нет отзывов