background image

Figure 3

1.

Fuel tank cap

CHECK THE HYDRAULIC SYSTEM

The hydraulic system operates on Mobil DTE 26 or
equivalent anti-wear hydraulic fluid.  The machine’s
reservoir is filled at the factory with fluid.  However,
check the level of hydraulic fluid before the engine is
first started and daily thereafter.

Figure 4

1.

Hydraulic reservoir

2.

Screen

3.

Fluid Level (9 cm) from top of fill hole

Hydraulic Oil (Recommended brands):

Mobile

DTE 26

Shell

Tellus 68

Amoco

Rykon Oil #68

Conoco

Super Hydraulic Oil 68

Exxon

Nuto 68

Kendall

Kenoil R&O AW 68

Pennzoil

Penreco 68

Phillips

Magnus A 68

Standard

Energol HLP 68

Sun

Sunvis 831 WR

Union

Unax AW 68

Chevron

AW Hydraulic Oil 68

Note: 

All are interchangeable.  Mobile SAE 10W30 or

10W40 may be substituted if the above oils are not
available.

IMPORTANT

Use only hydraulic oils specified.

Other fluids could cause system damage.

Note: 

A red dye additive for the hydraulic system oil is

available in 2/3 oz. bottles.  One bottle is sufficient
for 15–23 liters of hydraulic oil.  Order Part No.
44-2500 from your Authorized Toro Distributor.

1. 

Park the machine on a level surface.  Make sure the
machine has cooled down so the oil is cold.

2. 

Remove the cap from the top of the reservoir and
check the fluid level.  The fluid should be approxi-

12

Before Operating

Because diesel fuel is flammable, use caution when
storing or handling it.  Do not fill the fuel tank
while the engine is running, hot or when the
machine is in an enclosed area.  Vapors may build
up and be ignited by a spark or flame source many
feet away.  DO NOT SMOKE while filling the fuel
tank to prevent the possibility of an explosion.
Always fill the fuel tank outside and wipe up any
spilled diesel fuel before starting the engine.  Use a
funnel or spout to prevent spilling diesel fuel and
fill the tank to about 1 inch (25 mm) below the filler
neck.  Store diesel fuel in a clean safety-approved
container and keep the cap in place on the container.
Keep diesel fuel in a cool, well-ventilated place;
never in an enclosed area such as a hot storage shed.
To assure volatility and to prevent contamination. do
not buy more than a 6-month supply.

DANGER

Содержание 04375





























Отзывы: