background image

This product complies with all relevant European
directives, for details please see the separate product
specific Declaration of Conformity (DOC) sheet.

WARNING

CALIFORNIA

Proposition 65 Warning

The engine exhaust from this product

contains chemicals known to the State of

California to cause cancer, birth defects,

or other reproductive harm.

Important:

This engine is not equipped with a

spark arrester muffler. It is a violation of California
Public Resource Code Section 4442 to use or operate
the engine on any forest-covered, brush-covered, or
grass-covered land. Other states or federal areas
may have similar laws.

This spark ignition system complies with Canadian
ICES-002.

Introduction

This machine is a walk-behind, reel-blade lawn mower
intended to be used by professional, hired operators in
commercial applications. It is primarily designed for
cutting grass on well-maintained lawns in parks, golf
courses, sports fields, and on commercial grounds. It is
not designed for cutting brush, mowing grass and other
growth alongside highways, or for agricultural uses.

Read this information carefully to learn how to operate
and maintain your product properly and to avoid injury
and product damage. You are responsible for operating
the product properly and safely.

You may contact Toro directly at www.Toro.com for
product and accessory information, help finding a
dealer, or to register your product.

Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your product ready. Figure 1
identifies the location of the model and serial numbers
on the product. Write the numbers in the space
provided.

Figure 1

1.

Location of the model and serial numbers-Traction unit

Model No.

Serial No.

This manual identifies potential hazards and has
safety messages identified by the safety alert symbol
(Figure 2), which signals a hazard that may cause serious
injury or death if you do not follow the recommended
precautions.

Figure 2

1.

Safety alert symbol.

This manual uses two other words to highlight
information.

Important

calls attention to special

mechanical information and

Note

emphasizes general

information worthy of special attention.

© 2011—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420

2

Contact us at www.Toro.com.

Printed in the USA.

All Rights Reserved

Содержание 04025





































Отзывы: