Toro 04025 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 36

Toro 04025 Скачать руководство пользователя страница 15

Product Overview

Figure 15

1.

Handle

5.

Cutting unit

2.

Control panel

6.

Grass basket

3.

Engine

7.

Fuel tank

4.

Transport wheels

Controls

G009976

1

2

3

4

5

Figure 16

1.

Throttle control

4.

On/off switch

2.

Traction & reel drive
engagement lever

5.

Hour meter

3.

Service/parking brake

Throttle Control

The throttle control (Figure 16) is located on rear right
side of control panel. Lever connects to and operates
throttle linkage to carburetor. Engine speed can be
varied from 2400 RPM to 3600 RPM.

Traction and Reel Drive Engagement
Lever

The traction and reel drive engagement lever (Figure 16)
is located on front right side of control panel. Traction
lever has two positions: Neutral and Forward. Pushing
lever forward engages traction drive.

The reel drive lever has two positions: Engage and
Disengage. Move top of lever to the left to engage reel
or back to neutral to disengage reel.

Service/Parking Brake

The service/parking brake (Figure 16) is located on left
front side of control panel. Pulling the lever back over
center will set the parking brake. Brake must be released
before traction drive is engaged.

On/Off Switch

The on/off switch (Figure 16) is located on top of
control panel. Move switch to On position to start
engine and Off to stop engine.

Hour Meter

The hour meter (Figure 16), located on top of the
control panel, indicates the total hours of machine
operation.

Operator Presence Control

The optional operator presence control must be engaged
before engaging the traction lever or the engine will stop.

Choke Lever

The choke lever (Figure 17) is located on left front of
engine. Lever has two positions: Run and Choke. Move
the choke lever to the half-open position when starting
a cold engine. After engine starts move lever to Run
position.

Figure 17

1.

Choke lever

2.

Fuel shut-off valve

15

«
...
13
14
15
16
17
...
»

Содержание 04025





































Отзывы:

Нет отзывов