Toro 03781, Руководство по обслуживанию

Страница: 243 / 468

Reelmaster 7000−D Page 6 − 17 Electrical System
Settings Screen
The settings screen (Fig 17) allows the operator or tech-
nician to customize the InfoCenter display, modify a vari-
ety of machine functions, and provides access to unlock
various protected menus and settings. To scroll through
the list of functions, view its current setting, and select
(highlight) the setting to be modified, press the Down
button (as indicated by the
at the bottom of the
screen).
To return to the previous screen, press the Menu/Back
button (as indicated by the at the bottom of the
screen).
Units: Use the Left/Right button (as indicated by the
at the bottom of the screen) to select between metric or
English units of measure. Allow the desired selection to
remain in view for five (5) seconds. The fault indicator
will illuminate and an operator advisor
y #180 (New Val-
ue Saved in Permanent Memory) will a ppear on the Info-
Center display to confirm that the change has been
recorded.
Language: Use the Left/Right button (as indicated by
the at the botto m of the screen) to select from numer-
ous language options. Allow the desired selection to re-
main in view for five (5) seconds. The fault indicator will
illuminate and an operator advisor
y #180 (New Value
Saved in Permanent Memory) will a ppear on the Info-
Center display to confirm that the change has been
recorded.
Backlight: Press the Left/Right button (as indicated
by the at the bottom of the screen) then use the
Down button to decrease or the Left/Right button to in-
crease the InfoCenter Display brightness
(as indicated
by the − and the + at the bottom of the screen) .
Contrast : Press the Left/Right button (as indicated
by the at the bottom of the screen) then use the
Down button to decrease or the Left/Right button to in-
crease the InfoCenter Display contrast
(as indicated by
the − and the + at the bottom of the screen) .
F B’Lap RPM: Use the Left/Right button (as indicated
by the at the bottom of the screen) to select the reel
speed used when backlapping the front reels. Choose
from five (5) preset reel speeds.
R B’Lap RPM: Use the Left/Right button (as indicated
by the at the bottom of the screen) to select the reel
speed used when backlapping the rear reels. Choose
from five (5) preset reel speeds.
Settings
Units:
Language:
Backlight:
English
English
40%
1. Settings items
2. Left/Right button
3. Down button
4. Menu/Back button
Figure 17
4
3
2
1
SETTINGS SCREEN
Protected Menus: Authorized individuals can enter the
four (4) digit passcode (PIN) to reveal the following ser-
vice functions (see Faults Screen and Service Screen in
this chapter):
Clear System Faults
Service Timer Reset
DPF Regeneration
DPF Ash
Entering the correct PIN will also reveal and allow ad-
justment of various machine functions on the settings
screen if Protect Settings is set to ON (see Settings
Screen − Protect Settings).
Use the Down button and Left/Right button (as indicated
by the
and the at the bottom of the screen) to en-
ter the four (4) digit passcode (PIN). Once the correct
PIN has been entered, press the down button (as indi-
cated by the at the bottom of the screen). PIN will ap-
pear in the upper right hand corner of the InfoCenter
display. The protected items will be visible as long as the
ignition switch remains ON.
To edit the passcode (PIN), enter the current PIN as pre-
viously described (
PIN will appear in the upper right
hand corner). Select Protected Menus again and use
the Down button and Left/Right button (as indicated by
the
and the at the bottom of the screen) to enter
a new four (4) digit PIN. Press the Down button to save
the change (as indicated by the at the bottom of the
screen).
Electrical
System