background image

9

Strictly follow manufacturer/distributor 
indications for the maintenance and daily 
recharge of the batteries. All installation and 
maintenance operations must be executed 
by specialized staff, using suitable protection 
accessories.

BATTERY RECHARGER

Be sure that the battery recharger is suitable 
for the installed batteries both for their 
capacities and type (lead/acid or GEL and 
equivalent).

ON-BOARD BATTERY RECHARGER

The machine is equipped with the on-
board battery recharger.  Please refer to the 
manufactures instructions on the use of the 
charger.  The battery recharger is connected 
directly to the battery poles.  During the 
recharging operations a device is activated 
which does not permit the machine's 
functioning.  The main cable of the battery 
recharger has a maximum length of two meters 
and must be connected to a single-phase 
socket type CEE 7/7.

BATTERIES RECHARGING 

Bring the machine on a leveled surface near to 
a single-phase 120V 60 HZ socket (within 2 m), 
nominal current 10A.  Switch off the machine 
and proceed as follows.
1. Insert the plug into the mains socket.
2. Proceed with the recharging keeping the 
recovery tank lifted (see under paragraph 
“ACCESS TO THE BATTERY COMPARTMENT” 
in “BEFORE USE”).

Never charge a GEL battery with a non suitable 
recharger. Strictly follow the instructions 
supplied by the batteries and recharger 
manufacturer.  In order not to cause permanent 
damages to the batteries, it is necessary to 
avoid their complete discharge, providing 
for the recharging within a few minutes after 
batteries discharge signal starts blinking.

Never leave batteries completely discharged 
even if the machine is not used. In case of 
traditional batteries, please check the
electrolyte level every 20 recharging cycles and 
eventually fill them up with distilled water after 
having carried out a complete recharge.

Danger of gas exhalations and emission of 
corrosive liquids. Fire danger: do not approach 
with free flames.

BATTERIES DISPOSAL

It is compulsory to hand over exhaust batteries, 
classified as dangerous waste, to an authorized 
institution according to the current laws.

3. Do not take off the plug from the mains 
socket until the end of charge. At the end of 
the recharging, remove the plug from the mains 
socket.

Содержание BD 20/11L





















Отзывы: