background image

4

IMPORTANT SAFETY INSTRUCTIONS

FOR COMMERCIAL USE

WHEN USING AN ELECTRICAL APPLIANCE, BASIC PRECAUTIONS SHOULD

ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

Do not leave machine unattended when plugged in. Unplug from outlet when not in use and 
before changing pads or attempting any maintenance or adjustment. If handle switch lever is 
activated accidentally, high starting torque will cause machine to move and may cause damage 
or injury.
To avoid electrical shock, Use indoors only. Do not use outdoors and do not expose to rain.
Do not allow to be used as a toy. Close attention is necessary when used by or near children.
Use only as described in this manual. Use only manufacturer’s recommended attachments.
Do not use with damaged cord or plug. If machine is not working properly, if it was dropped,
damaged, left outdoors, or dropped into water, return it to a service center.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around 
sharp edges or corners. Do not run machine over cord. Keep cord away from heated surfaces. 
Do not unplug by pulling on cord. To unplug, grasp the plug not the cord.
Do not handle plug or machine with wet hands.
Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
Turn off all controls before unplugging.
Connect to a properly grounded outlet only. See Grounding Instructions.
Do not put hands under base - rotating parts could cause injury.
Always keep hands feet and loose fitting clothing away from moving parts to prevent possible 
injuries.
Use care to keep electrical supply cable from contacting moving parts, such as floor brushes or 
pads.

Risk of explosion

: Floor sanding can result in explosive mixture of fine dust and air. Use this

machine only in a well-ventilated area, free from any flame or match.
Do not use machine in areas where flammable and/or explosive vapors or dusts are present.
To avoid fires do not use with a flammable or combustible liquid to clean a floor.
Make sure voltage and frequency at the wall receptacle correspond with that indicated on 
nameplate before plugging in machine.
Use only a 12 Ga. three-wire extension cable, which have 3-prong grounding type plugs and 
3-prong receptacles that accept the plug of the machine.

SAVE THESE INSTRUCTIONS

Содержание 99409
















Отзывы: