background image

Attaching the Lubrication Pump 

32352  Rev 1 

12 

Tormach® PCNC 1100 Deluxe Stand 

 

9

 

Attaching the Lubrication Pump 

Beginning with Series 3 machines, the manual lubrication pump is located on the stand. Earlier models, 
had this mounted directly to the mill, however, this exposed the pump to the coolant stream and chip 
swarf which can, in some cases, pollute the lubrication oil in the pump. 

PCNC 1100 stands come with pre drilled holes to mount tube clips and both the manual or optional 
automatic oilers. Please see Figure 25. Please note, all parts listed below are included with the PCNC mill, 
not the Deluxe Stand. 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Left Coolant Tray 
2. Clips 
3. 4 mm OD Tube (31304) and Protective Sleeve (31306) 
4. Fitting- Nut with Ferrule (31409) 
5. Pump (30409) 
 
[Please note, PCNC 1100 Series 3 machines with Deluxe Stand's manufactured before September, 2011 
unfortunately do not have predrilled holes in the stand base. The owner will need to drill and tap these on 
their own. The pump (5) should sit about 6 inches below the underside of the left coolant tray (1).] 

 

 

Figure 25. Machine arm mounted to column. 

Содержание PCNC 1100 Deluxe Stand

















Отзывы: