background image

3

TROUBLE SHOOTING

SYSTEM AIR PURGE:

1. Turn release valve counterclockwise one full turn to open.

2. Pump handle eight full strokes.

3. Turn release valve clockwise to close valve.

4. Pump handle until the ram reaches maximum heigh and continue to pump several times to remove trapped 

air in the ram.

5. Carefully and slowly pinch oil fill plug to release trapped air.

6. Turn release valve counterclockwise one full turn and lower ram to the lowest position. Use force if 

necessary.

7. Turn release valve clockwise to closed position and check for proper pump action. It may be necessary to 

perform the above more than once to assume air is evacuated totally.

PROBLEM

POSSIBLE CAUSE

ACTION

Jack will not lift to full height

Low oil level

Check oil level

Jack will not hold load

Release valve not closing

Hydraulic jack oil contaminated

Pump valves not sealing

Cylinder ram binding

Call customer service

Jack will not lower

Cylinder ram binding

Parts worn

Internal damage

Call customer service

Jack feels spongy when lifting

See Air Purge section

See Air Purge procedure

WARNING!

1.   Study, understand, and follow all instructions before operating this device.

2.   Do not exceed rated capacity.

3.   Use only on hard, level surfaces, with less than 3 degrees of slope.

4.   Lifting device only. Immediately after lifting, support the vehicle with appropriate means.

5.   Do not move or dolly the vehicle while on the jack.

6.   Lift only on areas of the vehicle as specified by the vehicle manufacturer.

7.   No alterations shall be made to this product.

8.   Only attachments and/or adapters supplied by the manufacturer shall be used.

9.   Do not get under or allow anyone under the vehicle until it has been supported by jack stands.

10. Center load on saddle prior to lifting.

11. Use wheel chocks or other blocking device on opposing wheels before using jack.

12. Never use on a lawn mower or lawn tractor.

13. Do not use this jack for any use other than the manufacturer specified usage.

14. Do not rock the vehicle while working on or around equipment.

15. The following are not recommended for supporting on this equipment: Foundations, Homes, Mobile 

Homes, Trailers, RV’s, Campers, nor Fifth Wheels, etc... 

16. Failure to heed these markings may result in personal injury and/or property damage.

  WARRANTY NOTICE

This equipment is covered under a 1-year limited warranty when used as recommended. Only those 

items listed with a Part # are available for purchase. For assistance with the operation or the availability 

of replacement parts, contact our Parts and Warranty Department at www.torin-usa.com/support. Please 

have available a copy of your receipt, the model number of the product, serial number, and specific details 

regarding your question.

Not all equipment components are available for replacement; illustrations provided are a convenient reference 

of location and position in the assembly sequence.

The manufacturer reserves the rights to make design changes and or improvements to product lines 

and manuals without notice.

Содержание TH932001B













Отзывы: