16- PEAK LED
This red LED will let you know about the status of the signals processed into MX.6FX. Connect a
microphone or an instrument to MX.6FX and sing/play at normal volume. Set the level control of
that channel so that the PEAK LED lights-up only occasionally. If this LED is always on, you are
experiencing a lot of distortion and you should turn the TRIM control down or reduce the EQ
boosting. If this led never lights up, turn the TRIM control up again.
17- LEVEL
This knob controls the channel's level from -
to +15 dB.
MASTER SECTION
18
19
20
22
23
21
24
25 26
-30
0
-4
-10
POWER
PHANTOM
PHANTOM
10
CLIP
2TK TO
CTRL ROOM
2TK TO
CTRL ROOM
2TK TO MIX
L
R
MASTER AUX
MASTER AUX
SEND
18- MAIN MIX LEVEL
This knob controls the level of the signal sent to MAIN
OUTPUTS and TAPE OUT. Also AUX RETURNS signals will
be sent to this control.
19- PHONES/CONTROL ROOM LEVEL
This knob controls the signal sent to CONTROL ROOM
OUTPUT & PHONESOUTPUT.
20- OUTPUT LEVEL METERS
These consist of two column of 6 LEDs each ranging from -30 dB to +18 dB (CLIP). The 0 LED
corresponds to a level output of 0 dBu. The CLIP LEDs come to life when the output r18
dBu. Set the MAIN MIX level control so that the CLIP LEDs only flashes occasionally. In general,
you get a good mix level when the Meter LEDs operate in the range 0 to +10. If you 10,
you will get distortion. If even -30 LEDs are sleeping your signal-to-noise ratio will suffer.
21- AUX RETURNS (DFX)
This knob controls the level of effects received from the STEREO AUX RETURN sockets. Such signals
will be routed directly into the MAIN MIX. If you have no need to connect an external multi-effect,
you can use AUX RETURN inputs as additional instrument inputs &use this as Volume control.
22- 2TK TO CTRL ROOM
If you push down the 2TK TO CONTROL ROOM button, the 2 TRACK IN signal will be routed into
the Control Room output and the level will be adjusted by the Control Room knob nearby the
Main MIX LEVEL knob.
23- 2TK TO MIX
If you push down the 2TK TO MIX button, the 2 TRACK IN signal will be routed into the MAIN
output and will be adjusted by the MAIN MIX LEVEL knob.
24- PHANTOM PWR Switch
This button will apply +48 Volt Phantom Power only to the 2 XLR MIC input sockets. When
condenser microphones are not used, please make sure
that the Phantom Power is disengaged.
25- PHANTOM LED
This LED indicates when the PHANTOM POWER is engaged.
26- POWER LED
This LED indicates when your MX.6FX is switched-on.
30
27
29
28
10
8
9
PRESETS
1
12
11
7
4
5
6
3
2
13
14
15
16
1 VIBRAFLANGE
2 FUNKY
3 ROCKABILLY
4 BIGSTAGE
5
8
9
12
13
16
FX LEVEL
REVERB LEVEL
VIBRATO
FLANGER
CHORUS
PEAK
15- PAN/BAL
This is the PANORAMA control, or balance control. You can adjust the stereo image of the signal
via this control. Keep this control in center position and your signal will be positioned in middle
of stage. Turn this control fully counter clockwise and the signal will be present only on the left
speaker and vice-versa. Of course a large number of intermediate positions is available.
8
MX
REAR PANEL
31
31- AC INPUT
This connector is used to connect the supplied AC Adapter.
27- PRESETS
Adjust this control to select the desired effect. There are a total of 16 Factory presets available
including pitch-variations, Vibratos, Flanger, Chorus, etc.
28- FX LEVEL
This control is used to adjust the output level of FX signal, which can be varied from 0dB to 10dB.
29- REVERB LEVEL
This control is used to adjust the output level of the REVERB signal, which can be varied from
0dB to 10 dB. The digital reverb is independent from the other 16 Factory Presets so you can
add reverb in any amount over chorus,flanger, or just use reverb turning down FX LEVEL control.
30- PEAK LED
This LED lights up when the input signal is too strong.
Enjoy the sound!
1- Speakers should be placed in a position that allows for unobstructe sound projection. In
many instances is beneficial for speakers to be elevated on tripod stands to achieve
maximum dispersion and reach.
2- Use professional advice or service when hanging and installing speakers. Please take
precautions to secure them to prevent them from falling and hurting someone. Care should
be taken as to not damage the cabinet or its components. Please comply with all pertinent
Regulations.
3- Use quality cables. Using quality cables will ensure the best possible sound.
4- For best results match the speakers to a good amplifier that matches the wattage and
impedance of your speakers. Proper amplification power results in good quality audio
and longer component life. Check out the power requirement for your cabinet.
5- Avoid pointing a microphone directly at an amplified speaker doing so, could cause
feedback possibly damaging speaker components and your hearing.
DSP SECTION
Your MX.6FX includes a quite unique and innovative digital multi-effects with 24-bit resolution
and high dynamic range. Unlike other multi-effects where all the presets are available in a seq-
uence and vice a single control, MX.6FX multi-effect unit is organized with a 16 presets control
and relative Level control for vibrato and modulation controls such as chorus and flanger. You
can add reverb at any time with a separate Level control or you can just use the reverb keeping
the FX level control turned down.
9
MX
MX 6FX
.
OFF
NO
AC Input:
18V ~ 50/60Hz 1000mA
32- POWER SWITCH
This switch is used to turn the main power ON and OFF.
32
Содержание MX.6FX
Страница 2: ...MX 15 MX...
