Top Flite Cessna 182 ARF Скачать руководство пользователя страница 29

29

panel in place in the fuselage. It should fit snugly over 
the portion of the cockpit floor that rests on top of the 
fuel tank. Glue the instrument panel in position.

11. Glue the seats to the cockpit floor. Remember, 

the seats should also be removable in case the floor 
needs to be taken out. Hot glue works well for this. Small 
dots of medium or thick CA could also be used.

INSTALL THE SPINNER & PROPELLER

1. Locate the 

spinner hardware

. A two-stroke and 

four-stroke spinner nut are provided.

2. Ream your prop as necessary. Install the spinner 

backplate,  propeller,  propeller  washer  and  spinner 
nut  onto  the  engine  crankshaft.  If  you  installed  a 
four-stroke engine, use the four-stroke spinner nut.

3. Tighten the spinner cone to the backplate using 

the 4 x 45mm SHCS.

FINAL TOUCHES

1. Locate the small pin holes in the covering on the 

fuselage and wing for the 

wing struts

. Align the holes 

in the wing struts over the pin holes in the covering and 
confirm that they will line up (the end of the strut with 
the flat base is installed on the wing). If not, make new 
pin holes that align with the holes in the struts as near 
to the original pin holes as possible. When satisfied, 
drill 3/32" [2.4mm] holes at the pin holes into the strut 
mounting  blocks  underneath  the  fuselage  sheeting. 
Thread  a  #4  x  5/8"  [16mm]  self-tapping  screw  into 
each  hole  and  back  it  out.  Apply  a  couple  drops  of 
thin CA to each hole to harden the wood. Install the 
struts between the wing and fuselage using four #4 x 
5/8" [16mm] self-tapping screws. 

2. Roughen 1/4" [6mm] from one end of each metal 

antenna wire and clean the area with alcohol. Glue 
the antennas into the antenna bases as shown. We 
used thick CA. However, epoxy could also be used.

Содержание Cessna 182 ARF





































Отзывы: