Top Flight Models P-47 THUNDERBOLT Скачать руководство пользователя страница 2

Congratulations!

You now own the most accurate  R/C Stand-Off Scale kit ever produced.

We at Top Flite hope  that you will find this model the most pleasant to build,

inspiring to look at and exciting to  fly  that  you  have  constructed.

It is honest to point out, however, that while  this  model is no more  difficult - in

fact is simpler than most  comparable  kits to  make, R/C Scale  models generally are not
for the newcomer to this hobby. Previous modeling experience and  careful  attention to

craftsmanship are  necessary. Even the "old hand" will do well to study and follow the
instructions and guidance  given in this booklet.

It is our aim to have you say: "This is the finest model I have ever built."

TOP FLITE MODELS, INC.

ACKNOWLEDGEMENTS

The  staff of Top  Flite  wishes to acknowledge the assistance of the  following

individuals who contributed  their  time and  talent  to  the successful creation of this kit:

Col. JIM G1LHULY  (USAF  RET.)

ART SCHROEDER
ART SAB1N

CLARK MACOMBER

Top Flite Models, Inc.

WARNING

A RADIO CONTROLLED  MODEL  IS  NOT A "TOY".  CARE AND CAUTION
MUST BE TAKEN IN PROPERLY  BUILDING THE  MODEL AS WELL AS IN THE
INSTALLATION A N D USE OF THE RADIO CONTROL DEVICE. IT IS IMPORTANT

TO FOLLOW ALL DIRECTIONS AS TO CONSTRUCTION OF THIS  KIT AS WELL AS

INSTALLATION A N D USE OF THE ENGINE A N D RADIO GEAR. THE A D V I C E  A N D

ASSISTANCE OF A WELL-EXPERIENCED BUILDER  A N D PILOT A R E  ESSENTIAL.

DON'T  TAKE  CHANCES.  IMPROPER  BUILDING,  OPERATION OR  FLYING OF  THIS

MODEL MAY  RESULT IN SERIOUS  BODILY  I N J U R Y  TO OTHERS, TO YOURSELF
OR PROPERTY DAMAGE.

Содержание P-47 THUNDERBOLT

















Отзывы: