Top Flight Models P-47 THUNDERBOLT Скачать руководство пользователя страница 13

Страница: 13 / 16

WING

ALIGNMENT WEDGE

FIG. 18

STEP

Remove pins from spar and cover the top of right wing with
sheets prepared in Step 1. Allow to dry.

Switch wing alignment wedge back to left side, block right half
up 4-1/2, and sheet the top of the left side.

Allow to dry completely.

WING

HARDWOOD WING
DOWELS

REINFORCE CENTER WITH FABRIC

TAPE AFTER SHEETING

AILERON BELLCRANK
ASSEMBLY

FIG. 19

NOTE: IF RETRACTABLE LANDING GEAR IS TO BE USED,
FOLLOW INSTALLATION INSTRUCTIONS PROVIDED BY

GEAR MFG.

STEP

Install LANDING GEAR BLOCKS and key blocks. Drill 5/32
holes for gear strut.

Drill 1/4 holes in leading edges and install hardwood dowels.

Install aileron bellcrank assembly and aileron pushrod wires.
(See wing cross SECTION CC)

Sheet both bottom halfs marking location for landing gear.

Glue wing TIPS and FLAPS in place.

Glue fabric reinforcing TAPE to center section.

Sand ailerons to final shape. Glue W-16 (ply) insert in place in
each aileron.

W-16 (PLY)

INSERT

FLAPS

AILERON

WING TIP

LANDING GEAR

BLOCKS

LANDING GEAR
KEY BLOCK

Содержание P-47 THUNDERBOLT

















Результаты поиска

Содержание P-47 THUNDERBOLT

Отзывы:

Бренды по названию

Популярные бренды

Top Flight Models P-47 THUNDERBOLT, Инструкция по эксплуатации

Результаты поиска

Содержание P-47 THUNDERBOLT

Отзывы:

Бренды по названию

Популярные бренды