background image

 

 

11 

meter display Err05 

does  not  meet  the  conditions  of 
calibration

 

loaded  weight    is  less 

than 20kg 

Adjust the loaded weight 

13

Disposal of waste oil 

The waste hydraulic oil shall be disposed in terms of relative laws. And it is forbidden to pouring 
out anywhere

 

14

Warning 

!

 

14. 1 Please read the operation instruction carefully before you operate the hand pallet truck 
and learn about all the features of this type of hand pallet truck.

 

14. 2 if you want to let the truck down by controlling the hand knob, you should better lift the 
hand knob a little at first, and then let the truck down slowly. It is forbidden to pull the handle 
knob with great force, because rapid dropping could cause some damages to both the hand 
pallet truck and cargo 
14. 3 don’t rock the hand grip at a high speed and in a high frequency! 
14. 4 don’t load the cargo at a high speed

 

14. 5 do not overload the forks. Overloading could keep the hand pallet truck from working 
normally. 
14. 6 the gravity center of cargo should be in the middle of truck forks. The offset of cargo 
could make hand pallet truck out of balance

 

14. 7 don’t load loose or unstable goods! 
14. 8 don’t put the goods on the truck fork for a long time! 
 
14. 9 when the truck does not work, make sure that the truck forks are on the lowest position 
and the power should be cut off! 
14. 10 it is forbidden to load people and let them stand on the forks to slide. Don’t put any part 
of body below the cargo. 
14. 11 do not operate the unnamed position! 
14.12  The  truck  shall  be  used,  serviced  and  repaired  according  to  the  manufacturer’s 

requirements and shall not be modified or have attachments fitted without ensuring that 
the truck is still safe. 

14.13 Do not use the hand pallet truck at an insufficiently illuminated place! 
14.14 Do not park the hand pallet truck by turning the hand grip to the right! 
14.15 Do not use the hand pallet truck as bumper jack! 
14.16 The extremity of fork arms shall not be used as a lever to lift a load! 
14.17 It is forbidden to use the truck at places where a risk of unintentional movement exists. 
14.18 It is forbidden to contact the truck with goods or cargo directly! 
14.19 Do not use the hand pallet truck in a potentially explosive atmosphere! 
14.20 During the operation of the hand pallet truck, the operator should pay more attention to 

the feet and any body part so as to avoid the risk of being crushed! 

14.21  The  truck  shall  be  used,  serviced  and  repaired  according  to  the  manufacturer’s 

requirements 

 

Содержание 596365









Отзывы: