Recall Shortcut
• Press the right POWER button to activate the SOLDERING STATION.
• Press and hold the right POWER button together with a shortcut button (1, 2, or 3) to
recall a shortcut.
• The LCD display (9) will indicate the actual temperature “REAL”.
e) Temperature Compensation/Calibration
• Press and hold the right POWER button and the button on the hot air gun handle (1).
• The LCD display (9) will begin to blink and show “CAL”.
- Press UP or DOWN on the control panel (15).
- Press UP or DOWN using the hot air gun controls (2).
Press and hold UP or DOWN to rapidly adjust
values.
• Press SET on the control panel (15) to save the setting.
Replacing the fuse
Allow the hot air gun and soldering iron to cool down completely, then turn the main
power switch OFF (7) and disconnect the power cord from the socket (14).
• Remove the cover over the fuse holder (13) located at the back of the main unit.
• Use a blunt object such as a flat head screwdriver to gently pry the fuse out.
• Perform a continuity test on the fuse, e.g. with an appropriate meter (digital multimeter).
• If the fuse is defective, replace it with a new fuse of the same type (see “Technical data” at
the end of these operating instructions).
Never use a fuse with other specifications. Never bridge a defective fuse! This may
cause a fire or a fatal electric shock!
• Insert a replacement fuse until it clicks into place, then replace the protective cover.
• Connect the workstation to the mains and switch it back on.
If the fuse blows again, disconnect the workstation from the mains and ask a
technician to conduct a thorough inspection.
Troubleshooting
a) Soldering Iron
LCD
Error Message/
Fault Indication
Suggestions
There is no
temperature reading.
Please contact technical support
service or other technical
personnel.
The maximum
temperature was
exceeded.
Reduce the set temperature.
Switch the main power OFF, wait
20 minutes then turn back ON.
Please contact technical support
service or other technical
personnel.
b) Hot Air Gun
LCD
Error Message/Fault
Indication
Suggestion
There is no
temperature reading.
Please contact technical support
service or other technical
personnel.
The maximum
temperature was
exceeded.
• Reduce the temperature
setting.
• Switch the main power OFF,
wait 20 minutes then turn
back ON.
• If still receive the error code,
please contact technical
support service or other
technical personnel.
Care and Cleaning
a) Main Unit and Hot Air Gun
• These are generally maintenance free. Disconnect the product from the mains, and allow all
parts to cool down completely before each cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, fibre-free cloth.
b) Soldering Iron
• Always keep the tip tinned before switching off or storing for any period of time.
• Never clean the tip with coarse, abrasive materials like files.
• If oxide forms on the tip, lightly rub with abrasive paper, wipe clean, then immediately reheat
and re-tin the tip to prevent oxidation of the wettable surface.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the
environment.
Technical Data
a) Main Unit
Input voltage ................................. 230 V/AC, 50 Hz,
Power consumption ...................... max. 700 W
Fuse .............................................. T5A (230 V/AC)
Operating conditions ..................... 0 to 40 ºC, 0 - 80 % RH (non-condensing)
Storage conditions ........................ -20 to +80 ºC, 0 - 80 % RH (non-condensing)
Power cable .................................. Length: approx.140 cm (without connector and plug)
Dimensions (W x H x D) ............... 186 x 169 x 255 mm (without hot air gun holder)
Weight .......................................... 4252 g (main unit with hot air gun and holder)
b) Soldering Iron
Power consumption ...................... 50 W
Temperature range ....................... approx. 200 °C to 480 °C
Temperature accuracy .................. ±10 °C
Temperature offset ........................ ±50 °C
Temperature stability .................... ±2 °C
Tip to ground impedance .............. <2 Ω
Tip to ground voltage .................... <2 mV
Cable length ................................. 90 cm
Dimensions (ø x H) ....................... approx. 24 x 185 mm
Weight .......................................... 105 g
c) Soldering Iron Holder
Dimensions (W x H x D) ............... 71 x 84 x 155 mm
Weight .......................................... 260 g
d) Hot Air Gun
Power consumption ......................
550 W
Temperature range ....................... approx. 100 °C to 500 °C
Temperature accuracy .................. ±35 °C
Temperature stability .................... ±5 °C
Maximum airflow ........................... 23 L/min
Pump type .................................... Diaphragm
Nozzle tips .................................... (QFP) quad flat pack:10 x 10 mm
(QFP) quad flat pack:14 x 14 mm
Round: ø4 mm
Round: ø8 mm
Dimensions (Ø x H) ...................... 44 x 195 mm
Weight .......................................... 230 g
Cable length ................................. 90 cm
Visit the Conrad website and search Item No.: 2108712 for information about any
optional accessories, spares, or replacement parts.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights
including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represent the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
*2108712_v1_0919_02_dh_m_en
