Tool Shed TSBM Скачать руководство пользователя страница 8

 

 

 

 

OPERATION MANUAL 

www.thetoolshed.co.nz 

ASSEMBLY 

 

ASSEMBLING STAND 

All parts of the stand, except for the rubber feet, get assembled using 

carriage bolts, washers, and hex nuts. Attach the stand sides (Fig.4) (A) to 

the stand top (B). Make sure the switch opening in the stand side is on the 

same side as the V-belt opening in the stand top. Then, assemble the side 
braces (C) to the stand sides (A). Do not completely tighten the hex nuts at 

this time. 

 

Rubber Feet – 

Place the 4 rubber feet brackets (Fig.5) (A) on the stand 

corners, then install the rubber feet (B) using hex bolts and hex nuts. 

Motor Mount – 

Assemble the motor mount bracket (Fig.5) (C) to the stand. 

Fix one end to the stand top and the other end opposite the side brace. 

 

Now the stand is completely assembled, turn it over on its feet and tighten 

all the hex nuts.  
 

Motor – 

Assemble the motor (Fig.6) (A) to the motor mount bracket (B). 

Make sure the motor pulley is aligned with the V-belt opening in the stand 
top. Fix the motor to the motor mount bracket using hex bolts, spring 

washers and hex nuts (C). Do not completely tighten the hex nuts at this 

time. 

 

ASSEMBLING SWITCH AND POWER CORD 

It is necessary to install the switch, switch cover, strain relief and power 

cord to the stand. First place the switch (Fig.7) (A) into the switch opening 
in the stand and secure it in place using pan head screws, washers, 

star washers and hex nuts.  

 

Now the strain relief (B) and the power cord (C) get installed to the 

side of the stand, next to the switch. Undo the strain relief nut, insert 
the strain relief into the opening in the stand and thread the nut onto 

the back side of the strain relief. Insert the power cord wires through 

the strain relief. Make sure the wires reach the switch and the ground 
and tighten strain relief nut. 

 

The last step is to pass the power cord wires and the motor 

cord wires through the 2 openings in the switch cover (D). 

Now connect the wires as illustrated in Fig.3. Once this is 

done, fix the switch over in place using panhead screws, 

washers, and hex nuts. 

 

 

 
 

 

 

 
 

 

Содержание TSBM
















Отзывы: