TONO Theta 7000 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 26

TONO Theta 7000 Скачать руководство пользователя страница 8

- 6 -

(3) Wireless set

Before connecting, adjust SWR as follows:

In the case of output less then 10 W:

less than 1.5

In the case of output from 10 W to 100 W: less than 1.3
In the case of output from 100 W to 500 W:

less than 1.1

(i) Speaker

Solder the ancillary coaxial cable and a pin plug as shown in Fig. 3. After soldering,

connect the pin plug to the CW/BAUDOT pin jack of the Θ-7000 and the other end to an external
speaker terminal or an earphone terminal of a wireless set.

(ii) In CW mode

Connect the cable to a key jack for CW of a wireless set, check the polarity by a tester

and connect its plus (+) to the plus (+) of a screw terminal for CW of the computer; its minus (–) to
the minus (–) of the computer. Take care not to exceed the rated capacity of keying circuit of 1.5 A,
150 V.

(iii) In RTTY mode

° In the case of a wireless set with FSK function:
Connect the cable to a KEY jack for RTTY of the wireless set, check the polarity by a

tester and connect its plus (+) to the plus (+) screw terminal for FSK of the computer, its minus (–)
to the minus (–) terminal. Special care should be exercised not to exceed the rating: 1.5 A for the
maximum keying circuit current and 150 V for the maximum voltage.

° In the case of a wireless set without FSK function:
Solder the ancillary coaxial cable and a pin plug as shown in Fig. 3. After soldering,

connect the pin plug to a pin jack for AFSK of the Θ-7000 and the other end to a microphone terminal
of the wireless set. The shielding braids of the cable should be connected to GND side of the micro-
phone terminal.

(4) Key

For manipulation practice in CW mode, connect keys to a screw terminal for KEY of the com-

puter.

(5) Oscilloscope

Cross pattern can be observed with oscilloscope by the following procedures: solder the co-

axial cable or shield cable with two pin plugs respectively as shown in Fig. 3; after soldering, connect
the pin plugs to pin jacks, SYNCM and SYNCS; connect the cable in SYNCM to the V-axis input to the
oscilloscope and the cable in SYNCS to the H-axis input.

«
...
6
7
8
9
10
...
»

Содержание Theta 7000



























Отзывы:

Нет отзывов