background image

- 22 -

4.17  Application of a microcomputer as an intelligent terminal

In  the  case  that  serial  input  and  serial  output  of  a  microcomputer  module  are  compatible  with

TTL, TTL OUT and TTL IN of the computer can be used as an intelligent terminal of a microcomputer
module by connecting them respectlvely to serial input and serial output of the microcomputer mod-
ule.

4.18  Operating example

1. You may come to be at a loss for making sentences during transmitting from the keyboard in

RTTY mode. For such a case, prepare 32 characters of LTR in advance in either of the channels of the
battery  backed-up  memory.  Make  that  prepared  characters  put  out  repeatedly  several  times  while
writing  a  next  sentence  into  the  buffer  memory.  On  the  completion  of  writing,  push 

[SHIFT]

  and

[ESC]

 keys and stop the output from the channel. The sentence will be immediately put out from the

buffer memory.

2. If you want to repeated output of a sentence longer than 32 characters by easy operation, di-

vide it into some shorter parts and make it be memorized in some channels of the battery backed-up
memory in advance.

Set  NORM/TEST/TUNE  switch  to  TEST  position,  make  the  screen  cleared  and  make  the  putout

from  the  channels  in  order  of  the  sentence  to  write  in  the  screen.  After  writing  in,  push

[SEND | CH3]

  key  with  NORM/TEST/TUNE  switch  being  set  at  NORM.  The  sentence  will  be  put  out

continuously.

Содержание Theta 7000



























Отзывы: