Tomahawk JXPT36K Скачать руководство пользователя

Страница: 5 / 44

CAUTION

: Used without the safety alert symbol,

CAUTION

indicates a potentially

hazardous situation which, if not avoided, may result in property damage.

1.1 Laws Pertaining to Spark Arresters

Notice: State Health Safety Codes and Public Resources Codes specify that in certain

locations spark arresters be used on internal combustion engines that use hydrocarbon

fuels. A spark arrester is a device designed to prevent accidental discharge of sparks or

flames from the engine exhaust. Spark arresters are qualified and rated by the United

States Forest Service for this purpose.

In order to comply with local laws regarding spark arresters, consult the engine distributor

or the local Health and Safety Administrator.

1.2 Operating Safety

Familiarity and proper training are required for the safe operation of equipment!

Equipment operated improperly or by untrained personnel can be dangerous! Read

the operating instructions contained in both this manual and the engine manual and

familiarize yourself with the location and proper use of all controls. Inexperienced

operators should receive instruction from someone familiar with the equipment before

being allowed to operate the machine.

1.2.1 NEVER

allow anyone to operate this equipment without proper training. People

operating this equipment must be familiar with the risks and hazards associated with it.

1.2.2 NEVER

touch the engine or muﬀler while the engine is on or immediately after it has

been turned oﬀ. These areas get hot and may cause burns.

1.2.3 NEVER

use accessories or attachments that are not recommended by Tomahawk

Power. Damage to equipment and injury to the user may result.

1.2.4 NEVER

leave machine running unattended.

1.2.5 ALWAYS

be sure operator is familiar with proper safety precautions and operation

techniques before using machine.

1.2.6 ALWAYS

wear ANSI Z87.1-approved safety goggles or safety glasses with side shields,

or when needed, a face shield. Use a dust mask in dusty work conditions. Also use non-skid

safety shoes, hardhat, gloves, dust collection systems, and hearing protection when

appropriate. This applies to all persons in the work area.

1.2.7 ALWAYS

close fuel valve on engines equipped with one when machine is not being

operated.

1.2.8 ALWAYS

store equipment properly when it is not being used. Equipment should be

stored in a clean, dry location out of the reach of children.

WARNING

Содержание JXPT36K













































Результаты поиска

Содержание JXPT36K

Отзывы:

Похожие инструкции для JXPT36K

Бренды по названию

Популярные бренды

Tomahawk JXPT36K, Руководство по эксплуатации

Результаты поиска

Содержание JXPT36K

Отзывы:

Похожие инструкции для JXPT36K

Бренды по названию

Популярные бренды