Tokyo Hy-Power HL-2.5KFX Скачать руководство пользователя страница 21

Страница: 21 / 21

11-2 Safety

Circuits

In addition to the protection circuits above, there are other safety circuits

e amplifier.

urred during the transmission, stop

Thermal Switches Threshold

Heat Sink:

100

℃

Power Transformer: 130

℃

atically be relieved, when the internal heat cools

of Be sure to turn off AC power switch, before you leave the operation desk.

Otherwise AC power will be turned on for itself right after the cooling.

(inter-locked circuits) built in th

They directly shut down AC power line for the primary of the power transformer,

and if shut down, AC power lamp (green), LCD display and cooling fan will all go

off.

In case this shut down has suddenly occ

ansmitting first and wait for several minutes. Pull off AC power plug and check

whether or not AC main fuses are blown.

•

These shut-downs will autom

130

℃

Main Fuse

Cover Switch

12V Sub

Power

Supply

Relay

AC200V

Heat Sink X-former

Power

X-former

100

℃

AC Power Relay

Содержание HL-2.5KFX






















Результаты поиска

Содержание HL-2.5KFX

Отзывы:

Бренды по названию

Популярные бренды

Tokyo Hy-Power HL-2.5KFX, Инструкция по эксплуатации

Результаты поиска

Содержание HL-2.5KFX

Отзывы:

Бренды по названию

Популярные бренды