Toho Electronics TTM-339, Руководство по эксплуатации

Страница: 22 / 32

- 22 -
5.5 Common parameter setting mode SET 4 (1)
SET04
Name Setting content Initial value
1
SLH
SV limiter upper limit (*2) (*3)
Thermocouple/RTD input (
SLL
+ 5.0) to SV setting range upper limit ( ° C)
(
SLL
+ 5) to SV setting range upper limit ( ° C)
1200
Current/voltage input (
SLL
+ 50) to SV setting range upper limit (digit) 12000
2
SLL
SV limiter lower limit (*2) (*3)
Thermocouple/RTD input SV setting range lower limit to (
SLH
- 5.0) ( ° C)
SV setting range lower limit to (
SLH
- 5) ( ° C)
0
Current/voltage input (
SLH
- 50) to SV setting range lower limit (digit)
3
CNT
Control type setting
1 Primary...pid control Secondary---None
1
2 Primary---onoff control Secondary---None
3 Primary---pid control Secondary---pid control
4 Primary---pid control Secondary---onoff control
5 Primary---onoff control Secondary---onoff control
4
DIR
Forward/reverse operation setting
0 Reverse operation
0
1 Forward operation
5
MV1
Primary control operating amount 0.0 to 100.0 (%) 0.0
6
TUN
Tuning type setting
1 Primary auto-tuning
1 2 Secondary auto-tuning
3 Primary/secondary auto-tuning
7
ATG
AT coefficient setting 0.1 to 10.0 (times) 1.0
8
ATC
AT sensitivity setting
Thermocouple/RTD input 0.0 to 999.9 (°C) 0 to 999 (°C)
2
Voltage/current input 0 to 9999 (digit)
9
AT1
AT startup screen for PID No. 1 (low
temperature)
Startup starts/stops by setting a SV and using the RUN/STOP key.
Characters and PV are alternately displayed in the PV digit during AT.
The SV range is
SLL
to
PM1
.
0
10
AT2
AT startup screen for PID No. 2
(intermediate temperature)
Startup starts/stops by setting a SV and using the RUN/STOP key.
Characters and PV are alternately displayed in the PV digit during AT.
The SV range is
PM1
to
PM2
.
0
11
AT3
AT startup screen for PID No. 3 (high
temperature)
Startup starts/stops by setting a SV and using the RUN/STOP key.
Characters and PV are alternately displayed in the PV digit during AT.
The SV range is
PM2
to
SLH
.
10
12
ATALL
AT startup screen for PID No. 1~3
Use the RUN/STOP key for start and stop.
During the auto tuning, Character//PV is alternately displayed at PV
display, and No. 1 – 3/SV are alternately displayed at SV display.
13
P1
Proportional band setting for PID No. 1 (low temperature) 0.1 to 200.0 (%) 3.0
14
I1
Integral time setting for PID No. 1 (low temperature) 0 to 3600 (seconds) 0
15
D1
Derivative time setting for PID No. 1 (low temperature) 0 to 3600 (seconds) 0
16
PM1
Intermediate point 1 setting for the
PID range
Thermocouple/RTD input
SLL
to
SLH
- 5.0 ( ° C)
SLL
to
SLH
- 5 ( ° C) 0
Current/voltage input
SLL
to
SLH
- 50 (digit) 0
17
P2
Proportional band setting for PID No. 2 (intermediate
temperature)
0.1 to 200.0 (%)
3.0
18
I2
Integral time setting for PID No. 2 (intermediate temperature) 0 to 3600 (seconds) 0
19
D2
Derivative time setting for PID No. 2 (intermediate
temperature)
0 to 3600 (seconds) 0
20
PM2
Intermediate point 2 setting for the PID range
PM1
to
SLH
( ° C) 10
21
P3
Proportional band setting for PID No. 3 (high temperature) 0.1 to 200.0 (%) 3.0
22
I3
Integral time setting for PID No. 3 (high temperature) 0 to 3600 (seconds) 0
23
D3
Derivative time setting for PID No. 3 (high temperature) 0 to 3600 (seconds) 0
24
T1
Primary control proportional cycle 0.1 to 120.0 (seconds) 1.0
25
ARW
Anti-reset windup 0.0 to 110.0 (%) Function turned off at 110.0 (%) setting 110.0
26
PS1
Primary control loop abnormalityPV
variation setting
Thermocouple/RTD input 0.0 to 999.9 ( ° C) or 0 to 999 ( ° C)
0
Current/voltage input 0 to 9999 (digit)
27
LOP1
Primary control loop abnormality time
setting
0 to 3600 (seconds) 0
28
CMOD
Primary control off-point position
selection setting
0 SV unit setting
0
1 Upper
2 Middle
3 Lower
29
C1
Primary control sensitivity control
Thermocouple/RTD input 0.0 to 999.9 ( ° C) 0 to 999 ( ° C) 1
Current/voltage input 0 to 9999 (digit) 10
30
CP1
Primary control off-point position
Thermocouple/RTD input -999.9 to 999.9 ( ° C) -999 to 999 ( ° C)
0
Current/voltage input -9999 to 9999 (digit)